Asus K8N-DL - Manual (Page 84)

4 - 2 2 4 - 2 2 4 - 2 2 4 - 2 2 4 - 2 2 C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p
CAS# Latency (Tcl) [2.5] CAS# Latency (Tcl) [2.5] CAS# Latency (Tcl) [2.5] CAS# Latency (Tcl) [2.5] CAS# Latency (Tcl) [2.5]
Sets the latency (in clocks) between the DRAM read command and the
time the data actually becomes available.
Configuration options: [2] [2.5] [3]
Min RAS# Active Time (Tras) [ 8T] Min RAS# Active Time (Tras) [ 8T] Min RAS# Active Time (Tras) [ 8T] Min RAS# Active Time (Tras) [ 8T] Min RAS# Active Time (Tras) [ 8T]
Controls the number of DRAM clocks used for DRAM parameters.
Configuration options: [5T] [6T] [7T] [8T] [9T] [10T] [11T] [12T] [13T]
[14T] [15T]
RAS# to CAS# Delay (Trcd) [ 4T] RAS# to CAS# Delay (Trcd) [ 4T] RAS# to CAS# Delay (Trcd) [ 4T] RAS# to CAS# Delay (Trcd) [ 4T] RAS# to CAS# Delay (Trcd) [ 4T]
Controls the latency between the DRAM active command and the read/
write command. Configuration options: [2T] [3T] [4T] [5T] [6T] [7T]
Row Precharge Time (Trp) [ 2T] Row Precharge Time (Trp) [ 2T] Row Precharge Time (Trp) [ 2T] Row Precharge Time (Trp) [ 2T] Row Precharge Time (Trp) [ 2T]
Controls the idle clocks after issuing a precharge command to the DRAM.
Configuration options: [2T] [3T] [4T] [5T] [6T] [7T]
Node Memory Interleaving [Disabled] Node Memory Interleaving [Disabled] Node Memory Interleaving [Disabled] Node Memory Interleaving [Disabled] Node Memory Interleaving [Disabled]
Enables or disables memory interleaving. Configuration options: [Disabled]
[Enabled]
S/W Memory Hole Remapping [Enabled] S/W Memory Hole Remapping [Enabled] S/W Memory Hole Remapping [Enabled] S/W Memory Hole Remapping [Enabled] S/W Memory Hole Remapping [Enabled]
Allows memory hoisting/remapping of the memory-mapped I/O address
hole to above 4GB system memory. Configuration options: [Disabled]
[Enabled]
MTRR Mapping Mode [Continuous] MTRR Mapping Mode [Continuous] MTRR Mapping Mode [Continuous] MTRR Mapping Mode [Continuous] MTRR Mapping Mode [Continuous]
Allows selection of [Continuous] for standard mode, or [Discreet] for
aggressive mode. Configuration options: [Continuous] [Discreet]
Master ECC Enable [Enabled] Master ECC Enable [Enabled] Master ECC Enable [Enabled] Master ECC Enable [Enabled] Master ECC Enable [Enabled]
Enables or disables ECC check/correct mode. Configuration options:
[Disabled] [Enabled]
ECC Memory Interlock [At Least One] ECC Memory Interlock [At Least One] ECC Memory Interlock [At Least One] ECC Memory Interlock [At Least One] ECC Memory Interlock [At Least One]
Allows selection for DIMMs that are ECC-compliant. Configuration options:
[At Least One] [All are]
ECC MCE Enable [Disabled] ECC MCE Enable [Disabled] ECC MCE Enable [Disabled] ECC MCE Enable [Disabled] ECC MCE Enable [Disabled]
When set to [Enabled], a machine-check exception (#MC) occurs whenever
an machine-check error that may not be corrected is encountered.
Configuration options: [Disabled] [Enabled]