LG 22LG3DCH - Manual (Page 107)

COMMER
CIAL
MODE
SETUP
105
0 03 30 0 -- A AC CK K M MA AS SK K
M.P.I. Communication Parameter. Leave at default set-
ting unless changed by Pay-Per-View provider. When set
to 1, changes M.P.I. for some OCV boxes.
0 03 31 1 -- P PO OLLLL R RA AT TE E
M.P.I. Communication Parameter. Selects Poll Rate for
M.P.I. Leave at default setting unless changed by Pay-
Per-View provider. Step size of 16 ms.
0 03 32 2 -- T TIIM MIIN NG G P PU ULLS SE E
M.P.I. Communication Parameter. Leave at default set-
ting unless changed by Pay-Per-View provider. Sets
baud rate. Step size of 4.3 uS.
0 03 35 5 -- C CO OM MP PP PO OR RT T E EN N.. ((H HD DM MII 1 1 P Po orrtt E En naab bllee))
Enable/disables TV display panel HDMI 1 input jack.
Set to 0 to disable, set to 1 to enable.
0 03 39 9 -- R RE EA AR R A AU UX X E EN N.. ((R Reeaarr A Au uxx E En naab bllee))
Set to 1 to enable display panel rear AUX (Video 1)
input.
Set to 0 to disable display panel rear AUX (Video 1)
input.
0 04 46 6 -- S ST TR RT T A AU UX X S SR RC CE E ((S Sttaarrtt A Au uxx S So ou urrccee))
Sets the starting AUX source. At power up, TV will
tune to starting Aux source if item 004 Start Channel
is set to 0.
255 = Last Aux 1 = Composite Video/Audio
3 = HDMI
0 04 47 7 -- A AU UX X S ST TA AT TU US S
Set to 1 for M.P.I. AUX source to be reported as a
channel number instead of channel 0. Set to 0 to dis-
able AUX identification change. Controls M.P.I. status
channel response for AUX inputs.
0 05 53 3 -- D DIIS S.. C CH H--T TIIM ME E ((D Diissaab bllee C Ch haan nn neell--T Tiim mee))
Set to 1 to disable the Channel-Time display, Channel-
Time display will not appear. Set to 0 to enable the
Channel-Time display.
0 06 69 9 -- E EN N.. C CH H--T T C CO OLL.. ((E En naab bllee T Teexxtt C Cu usstto om m C Co ollo orr))
Set to 1 to enable custom color for the Channel-Time display.
Set to 0 to disable custom color for the Channel-Time display.
0 07 70 0 -- FFO OR R.. C CH H--T TIIM ME E ((T Teexxtt D Diissp pllaay y FFo orreeg grro ou un nd d
C Co ollo orr))
Set according to Color Chart.
0 = Black
3 = Cyan 6 = Yellow
1 = Blue 4 = Red 7 = White
2 = Green 5 = Violet
N No otteess:: Applies only to ‘Channel Not Available’ mes-
sage if item 073 is set to 1, enabled. If foreground
color and background color are the same, background
will be transparent.
0 07 71 1 -- B BC CK K.. C CH H--T TIIM ME E ((T Teexxtt D Diissp pllaay y B Baacckkg grro ou un nd d
C Co ollo orr))
Set according to Color Chart.
0 = Black
3 = Cyan 6 = Yellow
1 = Blue 4 = Red 7 = White
2 = Green 5 = Violet
N No otteess:: Applies only to ‘Channel Not Available’ mes-
sage if item 073 is set to 1, enabled. If foreground
color and background color are the same, background
will be transparent.
0 07 73 3 -- C CH H N NO OT T A AV VB BLLE E ((C Ch haan nn neell N No ott A Avvaaiillaab bllee))
If set to 1 and item 028 CHANNEL OVERRIDE is set
to 0, “NOT AVAILABLE” message is displayed when
directly accessing a channel not in the channel scan
list available in TV’s memory.
0 07 75 5 -- R RE EV VE ER RT T C CH H ((R Reevveerrtt tto o S Sttaarrtt C Ch haan nn neell))
If set to 1 and loss of M.P.I. communication occurs, TV
automatically tunes to the specified Start Channel.
0 07 77 7 -- Q QU UIIC CK K S SH HU UT TO OFFFF
Allows TV power Off event to be controlled by
Channel Up/Down buttons on the Remote Control, TV
Front Panel and Pillow Speaker. End user would push
and hold channel button down for time required to
have TV turn Off. Setting 0 = disabled. Value Range 0
- 17, each number represents 1/2 second. For example,
if set to 4, TV should turn Off after end user pressed
and held any channel button down for a few seconds.
0 07 78 8 -- U UP PN N M MS SB B ((U UP PN N M Mo osstt S Siig gn niiffiiccaan ntt B By yttee))
User programmable number, most significant byte
readable by M.P.I. command. Note: Not linked to serial
number.
0 07 79 9 -- U UP PN N M MS SB B--1 1 ((U UP PN N M Mo osstt S Siig gn niiffiiccaan ntt B By yttee--1 1))
User programmable number, most significant byte-1
readable by M.P.I. command. Not linked to serial num-
ber.
0 08 80 0 -- U UP PN N M MS SB B--2 2 ((U UP PN N M Mo osstt S Siig gn niiffiiccaan ntt B By yttee--2 2))
User programmable number, most significant byte-2
readable by M.P.I. command. Not linked to serial num-
ber.
0 08 81 1 -- U UP PN N LLS SB B ((U UP PN N LLeeaasstt S Siig gn niiffiiccaan ntt B By yttee))
User programmable number, least significant byte read-
able by M.P.I. command. Not linked to serial number.
Detailed Descriptions of Installer Menu Items
(Continued on next page)