Asus Motherboard P5VD2-MX - Manual (Page 42)

1 - 3 0 1 - 3 0 1 - 3 0 1 - 3 0 1 - 3 0 C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
1.5 Gb/s hard disk drives.
If you installed Serial ATA hard disk drives, you can can create a RAID
0, RAID 1, and JBOD configuration through the onboard VIA VT8237A
RAID controller.
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• The Serial ATA RAID feature (RAID 0, RAID 1, and JBOD) is available
only if you are using Windows
® 2000/2003 Server/XP operation
system.
• Install the Windows ® 2000 Service Pack 4, the Windows ® XP Service
Pack1 or later version before using Serial ATA.
• Please refer to section “O n b o a r d D e v i c e s C o n f i g u r a t i o n O n b o a r d D e v i c e s C o n f i g u r a t i o n O n b o a r d D e v i c e s C o n f i g u r a t i o n O n b o a r d D e v i c e s C o n f i g u r a t i o n O n b o a r d D e v i c e s C o n f i g u r a t i o n” in
the BIOS for details on SATA RAID configuration.
®
SATA connectors
GND
RSA
TA_TXP1
RSA
TA_TXN1
GND
RSA
TA_RXP1
RSA
TA_RXN1
GND
SATA1
GND
RSA
TA_TXP2
RSA
TA_TXN2
GND
RSA
TA_RXP2
RSA
TA_RXN2
GND
SATA2
4 . 4 . 4 . 4 . 4 . J m i c r o n S e r i a l A T A R A I D c o n n e c t o r ( 7 - p i n S A T A _ A ) J m i c r o n S e r i a l A T A R A I D c o n n e c t o r ( 7 - p i n S A T A _ A ) J m i c r o n S e r i a l A T A R A I D c o n n e c t o r ( 7 - p i n S A T A _ A ) J m i c r o n S e r i a l A T A R A I D c o n n e c t o r ( 7 - p i n S A T A _ A ) J m i c r o n S e r i a l A T A R A I D c o n n e c t o r ( 7 - p i n S A T A _ A )
This connector is for a Serial ATA signal cable for a Serial ATA hard
disk drive that you can combine with an external Serial ATA 3 Gb/s
device to configure a RAID 0, RAID 1, and JBOD set through the
onboard Jmicron SATA RAID controller.
Do not remove/unplug external SATA devices when running under RAID
mode.
®
SATA RAID connector
SATA_A
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND