Sandvik Coromant Threading - Manual (Page 103)

103
16 14 12 10 8 6 5 4 3
1 0.22 0.21 0.21 0.21 0.21 0.24 0.26 0.29 0.31
.009 .008 .008 .008 .008 .009 .010 .011 .012
2 0.21 0.20 0.20 0.20 0.20 0.23 0.26 0.28 0.31
.008 .008 .008 .008 .008 .009 .010 .011 .012
3 0.19 0.19 0.19 0.20 0.20 0.23 0.25 0.27 0.30
.008 .007 .007 .008 .008 .009 .010 .011 .012
4 0.17 0.17 0.18 0.19 0.19 0.22 0.24 0.27 0.29
.007 .007 .007 .007 .007 .009 .010 .010 .012
5 0.14 0.16 0.16 0.18 0.18 0.21 0.24 0.26 0.29
.006 .006 .006 .007 .007 .008 .009 .010 .011
6 0.08 0.13 0.15 0.17 0.17 0.21 0.23 0.25 0.28
.003 .005 .006 .007 .007 .008 .009 .010 .011
7 0.08 0.13 0.16 0.17 0.20 0.22 0.24 0.27
.003 .005 .006 .007 .008 .009 .010 .011
8 0.08 0.14 0.16 0.19 0.21 0.24 0.27
.003 .006 .006 .007 .008 .009 .011
9 0.12 0.15 0.18 0.20 0.23 0.26
.005 .006 .007 .008 .009 .010
10 0.08 0.13 0.17 0.19 0.22 0.25
.003 .005 .007 .008 .009 .010
11 0.12 0.16 0.18 0.21 0.24
.005 .006 .007 .008 .010
12 0.08 0.14 0.16 0.20 0.23
.003 .006 .006 .008 .009
13 0.10 0.15 0.18 0.22
.004 .006 .007 .009
14 0.10 0.17 0.21
.004 .007 .008
15 0.15 0.20
.006 .008
16 0.10 0.19
.004 .007
17 0.17
.007
18 0.15
.006
19 .100
.004
1.02 1.14 1.30 1.64 1.95 2.48 2.90 3.54 4.56
.040 .045 .051 .065 .077 .098 .114 .139 .180
CMC 02.1
MC P2.1.Z.AN
5. Technical reference
Extra stock is included in the total infeed 0.05 mm
.002 inch
Reference material
Thread turning infeed recommendations
ACME (AC), internal
Pitch, t.p.i.
No. of
infeeds
Unit Radial infeed per pass
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
Total infeed
mm
inch