Samsung SCX-8128NA-XAA - Manual (Page 149)

Troubleshooting_ 149
Right door is open.
Close it.
The door is not
securely latched.
Close the door until it
locks into place.
Scanner locked or
another problem
occurred.
The CCD (Charged
Couple Device) lock
has been locked.
Unlock the CCD lock . Or
turn the machine off and
back on again. If the
problem persists, call for
service. Scanner
Scan System
Failure [error
number]:Turn off
then on.
There is a problem in
the scan system.
Turn the machine off and
back on again. If the
problem persists, call for
service.
Second fax modem
card is not
installed. Install
the card.
The second optional
fax multiline kit is not
installed.
Install the optional fax
multiline kit. If it is already
installed, try to reinstall
the optional fax multiline
kit. If the problem
persists, call for service.
Shake [color] toner
cartridge.
Small amount of toner
is left in the indicated
cartridge.
You may temporarily
increase the printing
quality by redistributing
the toner (see
"Redistributing toner" on
page 125).
Side feeder door is
open. Close it.
The door is not
securely latched.
Close the door until it
locks into place.
Staple cartridge is
empty. Replace it.
The staple cartridge
has reached the end
of its lifespan.
This message appears
when the staple cartridge
is completely empty.
Replace the staple
cartridge.
Staple cartridge is
low. Replace
cartridge.
Small amount of
staple cartridge is left.
The estimated life of
staple cartridge is
close.
Prepare a new staple
cartridge for a
replacement.
Staple cartridge is
not installed.
Install it in finisher.
The staple cartridge is
not installed or the
staple cartridge is not
properly installed.
Install the staple
cartridge. If it is already
installed, try to reinstall
the staple cartridge. If the
problem persists, call for
service.
Staple cartridge of
booklet I is empty.
Replace cartridge.
The staple cartridge of
booklet has reached
the end of its lifespan.
This message appears
when the staple cartridge
is completely empty.
Replace the staple
cartridge.
Staple cartridge of
booklet I is low.
Replace cartridge.
Small amount of
staple cartridge of
booklet is left. The
estimated life of staple
cartridge is close.
Prepare a new staple
cartridge for a
replacement.
Message Meaning Suggested solutions
Staple cartridge of
booklet I is not
installed. Install
the cartridge.
The staple cartridge of
booklet is not installed
or the staple cartridge
is not properly
installed.
Install the staple
cartridge. If it is already
installed, try to reinstall
the staple cartridge. If the
problem persists, call for
service.
The clock became
initial time. Set a
time again.
The time setting of
machine is initialized.
Set the time setting in
Machine Setup.
Too much media in
the center tray.
Remove printed
media.
The center tray is full. Remove printouts from
the center tray, the
machine resumes
printing.
Too much media in
booklet tray.
Remove printed
media.
The booklet tray is full. Remove printouts from
the booklet tray, the
machine resumes
printing.
Too much media in
finisher tray.
Remove printed
media.
The finishing tray is
full.
Remove printouts from
the finishing tray, the
machine resumes
printing.
Top door of
scanner is open.
The duplex automatic
document feeder
cover is not securely
latched.
Close the cover until it
locks into place.
Transfer belt
cleaning unit is not
installed. Install it.
The transfer belt
cleaning unit is not
installed.
Power off/on, if the
problem persists, call for
service.
Transfer belt is not
installed. Install it.
The transfer belt is not
installed.
Power off/on, if the
problem persists, call for
service.
Transfer belt
cleaning unit is
worn. Replace with
new one.
The life of the transfer
belt cleaning unit
expires totally.
Replace the transfer belt
cleaning unit with a
Samsung-genuine
transfer belt cleaning
unit, call for service.
Transfer belt unit
is worn. Replace it.
The life of the transfer
belt unit expires
totally.
Replace the transfer belt
unit with a
Samsung-genuine
transfer belt unit, call for
service.
[tray number]
cassette is pulled
out. Insert it
properly.
The tray is not
securely latched.
Close the tray until it
locks into place.
[tray number] door
is open. Close it.
The tray is not
securely latched.
Close the tray until it
locks into place.
UI System Failure
[error
number]:Turn off
then on.
There is a problem in
the UI system.
Turn the machine off and
back on again. If the
problem persists, call for
service.
Message Meaning Suggested solutions