Sony FWD-42PV1 - Manual (Page 93)

45
(GB)
Specifications
Specifications
Video processing
Preset signal See page 25 (GB).
Sampling rate 13.5 MHz to 140 MHz
Panel system AC-type Plasma Display Panel
Display resolution 852 dots (horizontal)
× 480 lines
(vertical)
FWD-42PV1/42PV1A:
Pixel pitch
1.08 (horizontal)
× 1.08 (vertical)
mm ( 1 ⁄
16
×
1 ⁄
16
inches)
Picture size 920 (horizontal)
× 518 (vertical)
mm (36 1 ⁄
4
× 20
1 ⁄
2
inches)
Panel size 42-inch (diagonal 1056 mm)
FWD-42PV1P:
Pixel pitch
1.08 (horizontal)
× 1.08 (vertical)
mm ( 1 ⁄
16
×
1 ⁄
16
inches)
Picture size 518 (horizontal)
× 920 (vertical)
mm (20 1 ⁄
2
× 36 1 ⁄
4
inches)
Panel size 42-inch (diagonal 1056 mm)
Inputs and Outputs
INPUT1
DVI DVI (DVI Specification Rev. 1.0
compliant)
AUDIO Stereo minijack (
×1)
500 mVrms, high impedance
INPUT2
RGB/COMPONENT
D-sub 15-pin (female) (
×1) (See
“Pin assignment” on page 46
(GB).)
AUDIO Stereo minijack (
×1)
500 mVrms, high impedance
CONTROL S IN/OUT Minijack (
×2)
AUDIO OUT Pinjack (
×2)
500 mVrms, high impedance
REMOTE (RS-232C)
D-sub 9-pin (
×1)
SPEAKER 7 W + 7 W (6 ohms), direct
unbalanced impedance:
6-16 ohms
VIDEO/S VIDEO input/output adaptor
BKM-FW10
VIDEO (NTSC, PAL, SECAM, NTSC4.43,
PAL60, PAL-M, PAL-N)
VIDEO IN BNC (
×1)
Composite video, 1 Vp-p ±2 dB
sync negative, 75 ohms
(automatic termination)
VIDEO OUT BNC (
×1) Loop-through
S VIDEO IN Mini DIN 4-pin (
×1)
Y (luminance): 1 Vp-p ±2 dB sync
negative, 75 ohms terminated
C (chrominance): Burst
0.286 Vp-p ±2 dB (NTSC),
75 ohms terminated
Burst 0.3 Vp-p ±2 dB (PAL),
75 ohms terminated
S VIDEO OUT Mini DIN 4-pin (x1) Loop-through
AUDIO IN
Pinjack (
×2)
500 mVrms, high impedance
General
Power requirements
100 V to 240 V AC, 50/60 Hz,
FWD-42PV1/42PV1P/42PV1A:
3.5 A (Maximum)
Power consumption
FWD-42PV1/42PV1P/42PV1A:
260 W
AC OUT Maximum current rating: 0.25 A
or Maximum power
consumption: 30 W
Operating conditions
Temperature: 0 °C to +35 °C
(32 °F to 95 °F)
Humidity: 20
% to 90%
(no condensation)
Atomospheric pressure:
FWD-42PV1/42PV1P: 800 to
1100 hPa
Storing/transporting conditions
Temperature: –10 °C to +40 °C
(14 °F to 104 °F)
Humidity: 20
% to 90%
(no condensation)
Atomospheric pressure:
FWD-42PV1/42PV1P: 700 to
1100 hPa