Sony HT-DDW870 - Manual (Page 55)

Ad
dition
al I
n
fo
rm
atio
n
masterpage:Right
lename[E:\SEM_Janet\Revision_DDW870\J9040000_2549734121DDW870UCA\2549734121\
GB09ADD_HT-DDW870-UCA.fm]
55 GB
model name1[HT-DDW870]
[2-549-734-12(1)]
Models of area code AU
(6 ohms 120 Hz – 20 kHz, THD 0.09%)
FRONT
2)
: 50 W/ch
CENTER
2)
: 50 W
SURR
2)
: 50 W/ch
SURR BACK
2)
: 50 W
(6 ohms 1 kHz, THD 0.7%)
FRONT
2)
: 60 W/ch
CENTER 2) : 60 W
SURR
2)
: 60 W/ch
SURR BACK
2)
: 60 W
(6 ohms 1 kHz, THD 10%)
FRONT
2)
: 100 W/ch
CENTER
2)
: 100 W
SURR 2) : 100 W/ch
SURR BACK
2)
: 100 W
1) Measured under the following conditions:
2) Depending on the sound field settings and the
source, there may be no sound output.
Inputs (Analog)
Inputs (Digital)
Outputs (Analog)
Reproduction frequency range:
28 – 20,000 Hz
Tone
FM tuner section
Tuning range 87.5 - 108.0 MHz
Antenna FM wire antenna
Antenna terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
Models of area code U, CA
With 10-kHz tuning scale: 530 - 1,710 kHz
3)
With 9-kHz tuning scale: 531 - 1,710 kHz
3)
Models of area code CEL, CEK, SP, AU
With 9-kHz tuning scale: 531 – 1,602 kHz
Models of area code E51
With 10-kHz tuning scale: 530 - 1,610 kHz
3)
With 9-kHz tuning scale: 531 - 1,602 kHz
3)
Models of area code MX
With 10-kHz tuning scale: 530 - 1,610 kHz
Antenna
Loop antenna
Intermediate frequency 450 kHz
3) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off the
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
General
Power requirements
Area code Power requirements
U, CA 120 V AC, 60 Hz
MX 127 V AC, 60 Hz
CEL, CEK, SP 230 V AC, 50 Hz
AU, E51 240 V AC, 50 Hz
SA-CD/CD, MD/TAPE,
DVD, VIDEO 1, 2, 3 Sensitivity: 800 mV
Impedance: 50 k ohms
DVD (Coaxial) Sensitivity: –
Impedance: 75 ohms
VIDEO 2, SA-CD/CD
(Optical) Sensitivity: –
Impedance: –
MD/TAPE (OUT),
VIDEO 1 (AUDIO OUT) Voltage: 800 mV
Impedance: 10 k ohms
SUB WOOFER Voltage: 2 V
Impedance: 1 k ohm
Gain levels ±6 dB, 1 dB step
Area code Power requirements
U, CA 120 V AC, 60 Hz
MX 127 V AC, 60 Hz
CEL, CEK 230 V AC, 50/60 Hz
AU 240 V AC, 50 Hz
SP 220 – 230 V AC,
50/60 Hz
E51 120/220/240 V AC,
50/60 Hz
continued
GB01COV_HT-DDW870-UCA.book Page 55 Monday, December 20, 2004 2:00 PM