Alpine DVA-9861Ri - Manual (Page 20)

19
-EN
01GB05DVA9861Ri.fm
ALPINE DVA-9861Ri 68-04123Z62-A (EN)
Playing a Disc
Play Position Memory Function
Even if you turn power off or switch the Ignition Key to OFF during
playback or change the source, playback will continue from the point
where playback stopped when the power is turned ON again.
1
Press (OPEN).
The front panel will open.
2
Insert a disc with the label side facing up.
The disc will be pulled into the unit automatically.
Close the front panel manually.
When a disc is already inserted, press SOURCE/POWER
on the main unit to switch to the DISC mode.
The mode will change every time the button is pressed.
TUNER DISC IPOD* 1 CHANGER* 2 TUNER
* 1 Only when the iPod is connected
* 2 Only when the CD changer is connected
3
To eject the disc, press , after pressing (OPEN)
to open the front panel.
• Do not remove a disc during its eject cycle. Do not load more than
one disc at a time. A malfunction may result from doing either.
• If the disc does not eject, press and hold for at least 2 seconds.
• The reverse side of a double-sided DVD will not be played
automatically. Remove the disc, turn it over, and reinsert it.
• Never insert map discs for navigation purposes as they could damage
the equipment.
• Refer also to “DVD Setup” (pages 30 to 32).
On DVDs and video CDs with playback control (PBC), menu screens
may appear automatically. If this happens, perform the operation
described below to start playback.
• This operation is controlled using the remote control unit.
• For many discs, the menu screen can also be displayed by pressing
MENU.
DVD menu
Press , , or to select the desired item, then
press ENT.
• For some discs it is possible to select items directly from the menu
screen using the number keys (“0” to “9”).
• If the DVD-Audio disc is set to “VCAP”, operation can be
performed. (Refer to “Setting the DVD Audio Playback Mode” on
page 35.)
Video CD menu
Use the numeric keypad (“0” to “9”) to select the
desired number, then press ENT.
• The menu screen does not appear when the PBC function is turned
off. In this case, set VCD PLAY MODE to turn on the PBC function.
For details, refer to “Setting the Video CD Play Mode” (page 35).
Searching by Programme
• This operation is performed by the remote control unit.
1
Press and hold DISP./TOP M. for at least 2 seconds
while playing a DVD-VR disc.
The programme search list screen is displayed.
2
Press or to select the desired programme, then
press ENT.
The selected programme is played back.
• If PLAY LIST is selected, the playlist search list screen is displayed.
Searching by Playlist
• This operation is performed by the remote control unit.
1
Press MENU while playing DVD-VR disc.
The playlist search list screen is displayed.
2
Press or to select the desired playlist, then
press ENT.
The selected playlist is played back.
• Only discs containing a playlist can be used.
• If PROGRAM LIST is selected, the programme search list screen is
displayed.
Caution
• Not all functions will operate for every DVD. See the individual
DVD’s instructions for details on the features supported.
• Fingerprints on a disc may adversely affect playback. If a
problem occurs, remove the disc and check for fingerprints on the
playback side. Clean the disc if necessary.
• When using the remote control, be careful to press only one
button at a time. Pressing multiple buttons at the same time may
cause erroneous operation.
• If you try to perform an invalid operation (based on the type of
disc being played), the following mark is displayed on the
monitor screen:
If a menu screen appears
01GB00DVA9861Ri.book Page 19 Wednesday, December 7, 2005 12:00 PM