Alpine DVA-9861Ri - Manual (Page 40)

39
-EN
01GB05DVA9861Ri.fm
ALPINE DVA-9861Ri 68-04123Z62-A (EN)
8
Select the desired channel by pressing or ,
then press MODE.
When L+R is selected :
FRONT 1
FRONT 2 REAR CENTER
SUBWOOFER FRONT 1
When L/R is selected :
FRONT 1L
FRONT 1R FRONT 2L FRONT 2R
REAR L REAR R CENTER SUBWOOFER
FRONT 1L
• The speakers display differs, depending on the connected speakers.
9
Adjust the calculated time correction value (0.00 to
20.00ms) by turning the Rotary encoder, then
press MODE.
10
Switch the phase (PHASE 0° or 180°) by turning the
Rotary encoder, then press MODE.
11
To adjust other channels, repeat steps 8 to 10.
12
When the setting is complete, press and hold TA for
at least 2 seconds.
The unit returns to the normal mode.
• When the speaker is set to the “OFF” mode, the TCR for that
speaker cannot be set. Refer to “Setting the Speakers” (page 37).
• The adjustment value for FRONT2 (Speakers) which is adjusted in
time correction, is also applied to the front speakers in “Setting Bass
Focus” (page 41).
• The adjustment (AUTO TCR) cannot be automatically set on this
unit.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 44.
Graphic Equalizer Adjustments
The graphic equalizer allows you to modify the sound using 31 bands
each for the front (left and right), rear (left and right) and centre
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
1
Check that Defeat mode is off (page 25).
2
Press and hold TA for at least 2 seconds.
The audio processor control mode is activated.
3
Select the G-EQ mode by pressing TA repeatedly.
4
Select L+R or L/R by pressing and holding BAND for
at least 2 seconds.
When parametric EQ is adjusted, this setting will be turned
off.
5
Select the desired channel by pressing or ,
then press MODE.
When L+R is selected :
FRONT
REAR CENTER SUBWOOFER FRONT
When L/R is selected :
FRONT L
FRONT R REAR L REAR R CENTER
SUBWOOFER FRONT L
• The speakers display differs, depending on the connected speakers.
6
Select the frequency by turning the Rotary
encoder, then press MODE.
7
Adjust the level (LEVEL) (±9dB 1dB step) by turning
the Rotary encoder, then press MODE.
8
To adjust other frequencies, repeat steps 6 and 7.
9
To adjust other channels, repeat steps 5 to 8.
10
When the setting is complete, press and hold TA for
at least 2 seconds.
The unit returns to the normal mode.
• When the speaker is set to the “OFF” mode, the level of the graphic
equalizer for that speaker cannot be adjusted. Refer to “Setting the
Speakers” (page 37).
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker’s playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz
or 20 Hz band has no effect. Additionally, you may overload and
damage the speakers.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 44.
Switching the Phase
L+R: Sets the same adjustment values for the left and right
channels.
L/R: Different adjustment values can be set for the left and
right channels.
Adjustable frequency:
FRONT/REAR/CENTER: 20Hz - 20kHz (in 1/3 octave steps)
SUBWOOFER: 20Hz - 160Hz (in 1/3 octave
steps)
01GB00DVA9861Ri.book Page 39 Wednesday, December 7, 2005 12:00 PM