Panasonic SCAK331 - Manual (Page 27)

RQT7799
11
Front side
AM outdoor antenna
Run a piece of vinyl wire horizontally across a window or other
convenient location.
Leave the loop antenna connected.
AM loop
antenna
(included)
5 -12 m
1
2
AM outdoor antenna (not included)
Cassettes
Rear panel
of this unit
FM outdoor antenna
• Disconnect the FM indoor antenna.
• The antenna should be installed by a competent technician.
Optional antenna connections
Use outdoor antenna if radio reception is poor.
Note
Disconnect the outdoor antenna when the unit is not in use. Do not use the outdoor antenna during an electrical storm.
1
30 mm
15 mm
1
2
3
2
FM outdoor antenna
(not included)
75 Ω coaxial cable
(not included)
Shield braid
Core wire
Rear panel
of this unit
4 Press [; :, TAPE] to start playback.
Every time you press the button: / R F -
F - : The forward side (front side) will play.
/ R : The reverse side will play.
To stop tape playback
Press [L, STOP].
To fast-forward or rewind
Press [g/REW/
3] (rewind) or [f/FF/4] (fast-forward).
To select between loaded decks
Press [DECK 1/2] (remote control: [PLAY MODE]).
Note
• Tape playback is momentarily interrupted if you open the other
deck.
• Tapes exceeding 100 minutes are thin and can break or get caught
in the mechanism.
• Tape slack can get caught up in the mechanism and should be
taken up before the tape is played.
• Endless tapes can get caught up in the deck’s moving parts if used
incorrectly. Use tapes appropriate to this unit’s auto-reverse
mechanism.
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but this unit will
not be able to record or erase them correctly.
Preparation:
Wind up the leader tape so recording can begin immediately.
Press [;:, TAPE] then [L, STOP] to select tape as the source.
1 Press [DECK2 c] and insert the cassette to be
recorded.
The tape direction is automatically set to “F :”.
To record on the reverse side
Press [;:, TAPE] twice, then press [L, STOP]
2 Press and hold [PLAY MODE] on the remote control to
select the reverse mode.
Every time you press and hold the button:
: One side only records.
, : Both sides record (forward
reverse).
“ ” automatically changes to “ ” when [[, REC] is pressed.
Recording
3 Select the source to be recorded.
Radio recording:
Tune in the station. (A page 10)
Disc recording:
1 Insert the disc(s) you want to record.
Press [:/J, CD] and then [ L, STOP].
2 Prepare the desired disc recording mode.
Remote control only
• To record programmed tracks
On page 8, “Program play”, do steps:
CD 1 ~ 3
MP3 1 ~ 4
• To record specific discs/tracks
1. Press [PLAY MODE] to select the desired mode.
(A page 7)
2. Press [DISC] and then [1]–[5] to select the disc.
Ensure disc is stopped.
3. MP3 For 1-ALBUM mode and 1-SONG mode: Press
[ALBUM ( or )] to select the album.
4. For 1-SONG mode: Press [ g, REW/ 3] or
[f, 4/FF] to select the track.
Tape-to-tape recording:
1 Press [;:, TAPE] and then [L, STOP].
2 Press [c DECK1] and insert the cassette you want to record.
4 Press [a, REC] to start recording.
(Continued on next page)
You can use either deck 1 or deck 2 for tape playback.
Use normal position tapes.
High position and metal position tapes can be played, but the unit will
not be able to do full justice to the characteristics of these tapes.
1 Press [; :, TAPE].
The unit comes on. If a cassette was loaded, play starts
automatically (One touch play).
2 Press [c DECK1] or [DECK2 c] and insert the cassette.
Insert with the side to be played facing
towards you and the exposed tape
facing down. Close the holder by hand.
3 Press and hold [PLAY MODE] on the remote control to
select the reverse mode.
Every time you press and hold the button:
: One side is played.
: Both sides are played.
: Both sides are played repeatedly until [L, STOP] is pressed.
To listen to 2 tapes consecutively
Load a tape into each deck and select “
”. Both tapes will be
played repeatedly until [L, STOP] is pressed.
Playback