11 additional information, Troubleshooting, Additional information – Pioneer X-HM71-S User Manual

Page 32

Advertising
background image

11

11

32

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and

malfunctions. If you think that there is something wrong with

this component, check the points below. Sometimes the

trouble may lie in another component. Investigate the other

components and electrical appliances being used. If the

trouble cannot be rectified even after exercising the checks

listed below, ask your nearest Pioneer authorized service

center or your dealer to carry out repair work.

If the receiver does not operate normally due to external

effects such as static electricity disconnect the power plug

from the outlet and insert again to return to normal

operating conditions.

General

The clock is not set to the correct time.

 Did a power failure occur?

 Reset the clock (page 11).
When a button is pressed, the receiver does not respond.

 Set the receiver to the power standby mode and then turn it

back on.

 If the receiver still malfunctions, reset it (page 11).
No sound is heard.

 Is the volume level set to “Min”?

 Are the headphones connected?

 Are the speaker wires disconnected?
Settings you have made have been cleared.

 Was the power cord unplugged forcibly while this receiver’s

power was on?

Be sure to press

STANDBY/ON

and wait for

the

POWER

indicator on the front panel display to turn off

before unplugging the power cord.

Difference in volume between CDs, MP3, WMA, iPod/

iPhone/iPad and Tuner.

 This is not a problem with this receiver. The volume may sound

differently depending on the input source and recording

format.

This receiver cannot be operated with the remote control.
 Are you operating from far away?

Operate from within a

distance of Operate within 7 m, 30° of the remote sensor

on the front pan

el (page 5).

 Is the remote control sensor exposed to direct sunlight or

strong artificial light from a fluorescent bulb, etc.?

The remote

control signals may not be received properly if the remote

control sensor is exposed to direct sunlight or strong

artificial light from a fluorescent bulb, etc.

 Are the batteries dead?

Replace the batteries

(page 5)

.

The receiver suddenly switches off.

 When the Auto Power Off function is working, the power will

automatically turn off if the receiver has not operated for

several hours. Check the setting for the Auto Power Off

function (page 11).

X-HM81/XC-HM81 only: The Bluetooth wireless technology

device cannot be connected or operated. Sound from the
Bluetooth wireless technology device is not emitted or the
sound is interrupted.

 Check that no object that emits electromagnetic waves in the

2.4 GHz band (microwave oven, wireless LAN device or
Bluetooth

wireless technology apparatus) is near the receiver.

If such an object is near the receiver, set the receiver far from

it. Or, stop using the object emitting the electromagnetic

waves.

 Check that the Bluetooth wireless technology device is not too

far from the receiver and that obstructions are not set between

the Bluetooth wireless technology device and the receiver. Set

the Bluetooth wireless technology device and the receiver so

that the distance between them is less than about 10 m* and

no obstructions exist between them.
* The line-of-sight transmission distance is an estimate. Actual

transmission distances supported may differ depending on

surrounding conditions.

 Check that the Bluetooth ADAPTER and the ADAPTER PORT

terminal of the receiver are correctly connected.

 The Bluetooth wireless technology device may not be set to the

communication mode supporting the Bluetooth wireless

technology. Check the setting of the Bluetooth wireless

technology device.

 Check that pairing is correct. The pairing setting was deleted

from this receiver or the Bluetooth wireless technology device.

Reset the pairing.

 Check that the profile is correct. Use a Bluetooth wireless

technology device that supports A2DP profile and AVRCP

profile.

Tuner

The radio makes unusual noises continuously.

 Is the receiver placed near the TV or computer?

 Is the FM antenna or AM loop antenna placed properly? Move

the aerial away from the AC power cord if it is located nearby.

Disc playback

Playback does not start. Playback stops in the middle or is

not performed properly.

 Is the disc loaded upside down?

 Does the disc satisfy the standards?

 Is the disc distorted or scratched?
Playback sounds are skipped, or stopped in the middle of a

track.

 Is the receiver located near excessive vibrations?

 Is the disc very dirty?

 Has condensation formed inside the receiver?
Disc cannot be played or disc is ejected automatically.
 Is the disc scratched?

Scratched discs may not play.

 Is the disc dirty? Wipe the dirt off the disc

(page 36).

 Is the disc properly placed? Place a disc with the label side

facing front.

 Is this receiver placed in a humid location? There could be

condensation inside. Wait a while for the condensation to

evaporate. Do not place this receiver near an air-conditioner,

etc.

(page 36).

Sound is intermittent during disc playback.

 Sound volume may be too high. Sound and image may be

unsteady if sound volume is set too high; in this case, lower the

sound volume.

When a USB storage device is connected

USB storage device is not recognized.
 Is the USB storage device properly connected?

Connect the

device securely (all the way in).

 Is the USB storage device connected via a USB hub? This

receiver does not support USB hubs. Connect the USB storage

device directly.

 This is not a problem with this receiver. Turn the power off then

back on. Some USB storage devices may not be recognized

properly. This receiver only supports USB mass storage class

devices. Only the FAT16 and FAT32 file systems are supported.

Other file systems (ex. FAT, NTFS, etc.) are not supported. This

device does not support the use of external hard disc drives.

Much time is required to recognize the USB storage device.
 What is the USB storage devices capacity?

Some time may

be required to load the data when large capacity USB

storage devices are connected (this could take several

minutes).

Advertising
This manual is related to the following products: