Pioneer SC-LX85 - Manual (Page 63)

63 En
09 Using other functions
! The synchronized amp mode is canceled
when the HDMI output is switched. If you wish
to use the synchronized amp mode, switch to
HDMI OUT 1, then select the synchronized
amp mode on the TV using the TV’s remote
control.
About the Speaker B Link function
When 7.1ch + Speaker B or
5.1ch + SP-B Bi-Amp is selected for the
Speaker System setting (page 87) and the
Speaker B Link setting (HDMI Setup on page
54) is turned on, the setting of the played
speaker terminals switches automatically when
HDMI OUT is switched.
The settings switch as follows:
! HDMI OUT ALL – Switches to SP: A+B ON.
Sound is output simultaneously in the room
where the A speakers are located and in the
room where the B speakers are located.
! HDMI OUT 1 – Switches to SP: A ON. Sound
is only output in the room where the A
speakers are located.
! HDMI OUT 2 – Switches to SP: B ON. Sound
is only output in the room where the B
speakers are located.
Checking your system settings
Use the status display screen to check your
current settings for features such as surround
back channel processing and your current
MCACC preset.
1 Set the remote control to the receiver
operation mode, then press STATUS to
check the system settings.
The front panel display shows each of the fol-
lowing settings for three seconds each: Input
Source
d Sampling Frequency d MCACC
preset d ZONE 2 input d ZONE 3 input d
HDMI OUT.
2 When you’re finished, press STATUS
again to switch off the display.
Resetting the system
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this. Set MULTI-ZONE to
MULTI ZONE OFF.
! Disconnect the iPod and USB memory device
from the receiver beforehand.
! Set the Control with HDMI to OFF (see HDMI
Setup on page 54).
1 Switch the receiver into standby.
2 While holding down ENTER on the
front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET k/l,
then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.
! Note that all settings will be saved, even if the
receiver is unplugged.
Default system settings
Setting Default
Digital Video Converter ON
SPEAKERS FH/FW
Speaker System 9.1ch FH/FW
Speaker Setting
Front SMALL
Center SMALL
FH/FW SMALL
Surr SMALL
SB SMALLx2
SW YES
Surround Position IN REAR
Crossover 80 Hz
X-Curve OFF
DIMMER
Medium
bright
Inputs
See Input function default and possible settings on
page 36.
HDMI
HDMI Audio
Amp
HDMI output
HDMI OUT
ALL
Control ON
Control Mode ALL
Display Power Off YES
Audio playback
Power On Level
LAST
Volume Limit OFF
Mute Level FULL
Phase Control ON
Auto Sound
Retriever
iPod/USB,
HOME MEDIA
GALLERY,
ADAPTER PORT
input function
ON
Other input
functions
OFF
Setting Default
Sound Delay 0.0 frame
Dual Mono CH1
DRC AUTO
SACD Gain 0 dB
LFE Attenuate 0 dB
Auto delay OFF
Digital Safety OFF
Effect Level
ExtendedStereo 90
Other modes 50
2 PL II Music
Options
Center Width 3
Dimension 0
Panorama OFF
Neo:X Options Center Gain
Neo:X
CINEMA: 1.0
Neo:X
MUSIC: 0.3
Neo:X
GAME: 1.0
2 PL IIz Options Height Gain MID
All Inputs
Listening Mode
(2 ch/multi ch) AUTO
SURROUND
Listening Mode
(Headphones)
STEREO
See also Setting the Audio options on page 57 for
other default DSP settings.
MCACC
MCACC Position Memory
M1:
MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance (M1 to M6) 3.00 m
Standing Wave
(M1 to M6)
ATT of all chan-
nels/filters
0.0 dB
SWch Wide Trim 0.0 dB
EQ Data (M1
to M6)
All channels/
bands
0.0 dB
EQ Wide Trim 0.0 dB