Pioneer SC-LX85 - Manual (Page 66)

Resetting the remote control
settings
Use this procedure to reset all the remote con-
trol’s settings to the factory default.
When preset codes are set, all the signals
learned in the input function buttons are
cleared. This function is convenient when you
want to reset some but not all of input function
buttons.
1 While pressing MULTI OPERATION,
press HOME MENU.
The remote display shows SETUP MENU.
2 Use i/j to select ‘ALL RESET’, then
press ENTER.
ALL RESET flashes in the remote display.
3 Press and hold ENTER for about two
seconds.
The remote display shows OK to confirm the
remote presets have been erased.
Confirming preset codes
Use this feature to check which preset code is
assigned to an input function button.
1 While pressing MULTI OPERATION,
press HOME MENU.
The remote display shows SETUP MENU.
2 Use i/j to select ‘READ PRESET ID’,
then press ENTER.
The remote display prompts you for the input
function button you want to check.
3 Press the input function button of the
component for which you want to check
the preset code, then press ENTER.
The brand name and preset code appears in the
display for three seconds.
Renaming input function
names manually
You can customize the names that appear on
the remote display when you select an input
function (for example, you could change the
name of DVR/BDR to DVR-LX61).
1 While pressing MULTI OPERATION,
press HOME MENU.
The remote display shows SETUP MENU.
2 Use i/j to select ‘RENAME’, then
press ENTER.
The remote display prompts you for the button
of the input function you want to rename.
3 Press the input function button you
want to rename then press ENTER.
The TV CONTROL name can be changed when
the remote control operation selector switch
is switched to TV. To change the names of the
input functions, set the remote control opera-
tion selector switch to SOURCE.
4 Use i/j to select ‘NAME EDIT’, then
press ENTER.
To reset the button to its original (default)
name, select NAME RESET above.
5 Edit the name of the input function
in the remote control display, pressing
ENTER when you’re finished.
Use i/j to change the character and k/l to
move forward/back a position. The name can be
up to 14 characters.
Direct function
! Default setting: ON
You can use the direct function feature to con-
trol one component using the remote control
while at the same time, using your receiver to
playback a different component. This could let
you, for example, use the remote control to set
up and listen to a CD on the receiver, and then
En 66
10 Controlling the rest of your system (In case of SC-LX85)
Note
! Note that interference from TVs or other
devices will sometimes result in the remote
control learning the wrong signal.
! Some commands from other remote controls
cannot be learned, but in most cases the
remotes just need to be moved closer together
or farther apart.
! If the remote display shows MEMORY FULL,
it means the memory is full. See Erasing one
of the remote control button settings on page
66 to erase a programmed button you’re not
using to free up more memory (note that some
signals may take more memory than others).
! Depending on the type of command that has
been learned, operation may not be possible
with RF two-way communications. In this
case, operate using IR signal transmission.
For instructions on switching between
the IR and RF modes, see Operating other
components by RF communications on page
71.
Erasing one of the remote
control button settings
This erases one of the buttons you have pro-
grammed and restores the button to the factory
default.
1 While pressing MULTI OPERATION,
press HOME MENU.
The remote display shows SETUP MENU.
2 Use i/j to select ‘ERASE LEARNING’,
then press ENTER.
The remote display prompts you for the compo-
nent corresponding to the button setting to be
erased.
3 Press the input function button
corresponding to the command to be
erased, then press ENTER.
The remote display flashes PRESS KEY.
4 Press and hold the button to be erased
for two seconds.
The remote display shows OK or NO CODE to
confirm the button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold MULTI OPERATION for a
couple of seconds when you’re done.
Resetting the input
assignment of one of the
input function buttons
This procedure resets the input assignment
preset at the remote control’s input function
button, restoring the default.
1 While pressing MULTI OPERATION,
press HOME MENU.
The remote display shows SETUP MENU.
2 Use i/j to select ‘KEY RESET’, then
press ENTER.
The remote display prompts you for the compo-
nent corresponding to the button setting to be
erased.
3 Press the input function button for the
component whose input assignment you
want to reset, then press and hold ENTER
for a couple of seconds.
The remote display shows OK when the input
assignment of the remote control’s input func-
tion button is reset.