Sharp MX-M232D - Manual (Page 112)

110
SYSTEM SETTINGS
FW. RX DATA
This setting is used to select whether or not received
faxes are forwarded to a fax machine programmed as
explained in "RECEIVED DATA FW. STATION SET"
(page 110) in the event that the machine cannot print
the faxes. The setting is initially disabled.
1 Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 98).
2 Select "RCV. FUNCTION" with the [ ] or
[ ] key and then press the [OK] key.
3 Select "FW. RX DATA" with the [ ] or [ ]
key and then press the [OK] key.
• The setting is enabled and a checkmark appears in
the checkbox.
• If the procedure is performed when the setting is
enabled, the checkmark will be cleared and the
setting disabled.
RECEIVED DATA FW. STATION SET
When a problem prevents the machine from printing a
received fax, the fax forwarding function (page 49) can
be used to forward the received fax to another fax
machine. Use this setting to program the fax number of
the destination fax machine. Only one fax number can
be programmed (maximum of 50 digits).
To specify an F-code confidential box in the
destination fax machine, enter the sub-address and
passcode after the fax number in steps 6 and 7 below.
1 Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 98).
2 Select "RCV. FUNCTION" with the [ ] or
[ ] key and then press the [OK] key.
3 Select "RECEIVED DATA FW. STATION
SET" with the [
] or [ ] key and then
press the [OK] key.
4 Select "STORE" with the [ ] or [ ] key
and then press the [OK] key.
5 Enter the forwarding fax number with the
numeric keys and then press the [OK] key.
6 Enter the sub-address with the numeric
keys and then press the [OK] key.
If you do not need to specify an F-code confidential box
in the destination fax machine, press the [OK] key
without entering anything.
7 Enter the passcode with the numeric keys
and then press the [OK] key.
If you do not need to specify an F-code confidential box
in the destination fax machine, press the [OK] key
without entering anything.
EARLIER OUTPUT
When a received fax cannot be printed because the
machine is out of appropriate paper and a fax is
subsequently received that can be printed, this setting
determines whether the subsequent fax is printed
before the fax that cannot be printed. The setting is
initially enabled (the subsequent fax is printed first).
1 Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 98).
2 Select "RCV. FUNCTION" with the [ ] or
[ ] key and then press the [OK] key.
3 Select "EARLIER OUTPUT" with the [ ] or
[ ] key and then press the [OK] key.
• The setting is enabled (the subsequent fax is printed
first) and a checkmark appears in the checkbox.
• If the procedure is performed when the setting is
enabled, the checkmark will be cleared and the
setting disabled.
ANTI JUNK FAX
When this setting is enabled, reception from fax
numbers programmed using the "ENTER JUNK FAX
#" program will be blocked.
This program is normally disabled.
1 Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 98).
2 Select "RCV. FUNCTION" with the [ ] or
[ ] key and then press the [OK] key.
3 Select "ANTI JUNK FAX" with the [ ] or
[ ] key and then press the [OK] key.
• The setting is enabled and a checkmark appears in
the checkbox.
• If this procedure is performed when the setting is
enabled, the checkmark will be cleared and the
setting disabled.
This setting only operates when the fax
number of the machine that is to receive the
forwarded faxes is programmed.
Note
To delete the number, follow these steps:
(1) Select "DELETE" in step 4 and then
press the [OK] key.
(2) Select "DELETE" with the [ ] or [ ]
key and then press the [OK] key.
Note