Bosch WTMC5521 - Manual (Page 9)

9
LP - Gas Kit
part no. WTZ1280
The parts required for the LP version
can be obtained from your local dealer.
Please follow the installation
instructions supplied by the appropriate
manufacturer!
If you have a propane gas dryer and
need to convert it to natural gas,
(Service Kit 496297) please consult
your customer service agent for
assistance.
Note:
Dryer must be checked for proper
operation whenever the gas
connections have been broken.
Bottom exhaust kit
part no. WTZ1270
Note:
The maximum permitted number of 90°
elbows (including this side exhaust kit)
is four!
Dryer rack
part no. WTZ 1290
Use the dryer rack to dry washable
woolen textiles (e.g. sweaters) and
shoes.
Left hinge kit
part no. WTZ 1260 for all dryers except
silver and duo tone silver
part no.
WTZ 126S for silver and duo
tone silver dryers
The door catch can be reversed if
necessary. The door is hinged on the
right at the factory.
Pedestal Mounting Kit
part no. WTZ 1295 (White Dryers)
part no. WTZ 1295S (Silver Dryers)
part. no. WTZ 1295P (Duo tone Silver)
part. no. WTZ 1295R (Duo tone Red)
If mounting the dryer on the pedestal
follow the instructions supplied with the
pedestal.
Mobile home kit
part no. WTZ 1275
Note:
Please check with the Authority Having
Jurisdiction in your area to verify if a gas
dryer can be installed in your mobile
home. Once that has been verified,
installation of the dryer shall conform to
the Manufactured Home Construction
and Safety Standard, Title 24 CFR, Part
3280 {formerly the Federal Standard for
Mobile Home Construction and Safety,
Title 24, HUD (Part 280)}, and/or
Standard CAN/CSAĆZ240 MH.
Please use mobile home kit number
WTZ 1275 for means to secure the
dryer to the structure.
See page 9 Exhaust Air Connection"
for the exhaust duct installation
instructions.
The exhaust duct must be securely
fastened to a noncombustible portion
of the mobile home structure and must
not terminate beneath the mobile
home.
An opening to the outside must be
provided during installation. Insure that
the free area of the opening for the
introduction of outside air is not less
than twice the area of the dryer exhaust
outlet or use at least a 5 inch diameter
exhaust or at least a 25 in 2 square
exhaust duct for the opening.
Installation ć step by step
1. Unpack the dryer.
2. Remove all objects from the drum.
3. Check the dryer for visible
damage.
4. Position the dryer near the
installation location.
5. If required, have customer service
change the door hinges to the left
(see page 6).
6. If required, have customer service
install the exhaust air outlet on the
dryer (see page 7).
7. Have the gas supply connected by
an qualified technician (see page
7).
8. Install exhaust duct, if necessary.
Follow the installation instructions
supplied by the appropriate
manufacturer!
i If space is very restricted, it is
recommended to fit the initial parts
of the exhaust duct to the dryer
before the dryer is moved to its
final installation location.
9. Move the dryer to its final location
and align.
ATTENTION
Do not slide dryer across the floor if
heightĆadjustable feet have been
extended. Feet and/or dryer base
may be damaged if dryer is slid
across floor with heightĆadjustable
feet extended.
10. Position and then level the dryer .
The dryer should be level with all
four feet firmly on the ground. The
dryer must not wobble. If the dryer
is not level or if it does wobble, the
feet must be adjusted. Adjust the
heightĆadjustable feet until the
dryer does not rock and is level,
both frontĆtoĆback and
sideĆtoĆside.
11. Connect the exhaust duct to the
exhaust air outlet on the dryer.
12. Insert plug into the wall receptacle.