Advanced system functions – CompuSTAR RF-2W940-SS (Remote 2W940R-SS) User Manual
Page 12
23 By Firstech, LLC
Advanced System Functions
The RPS is an optional feature. The car call/RPS feature uses a small sensor that is mounted on the inside of your windshield.
RPS Touch (Remote Paging Sensor)
The new RPS touch has multiple features including: remote paging, 4 digit pin unlock/disarm, and arm/lock. All features are operated with a simple touch of the sensor.
Please have your installer program Option 3-16 to Setting 2.
RPS Touch and car call functions do not require programming, however in order to unlock/disarm your vehicle you must program a 4 digit passcode using the
instructions below:
STEP 1: Choose your RPS Touch 4 digit code. ᴖ0ᴗis not available.
STEP 2: Turn ignition to the ᴖONᴗposition and leave driverᴗ
s door open.
STEP 3: Hold your finger over the ᴖRed Circleᴗicon for 2.5 seconds.
STEP 4: When the siren chirps and LEDs flash in a circular pattern, tap on your first number. (Hold the number for 2.5 seconds to choose 6 through 10.) After
choosing your first number you will get one siren chirp and LEDs will flash in a circular pattern.
STEP 5: Repeat Step 4 until all four digits are set. You will get 1 siren chirp and 1 parking light flash. Repeat Steps 2 - 5 if you get 3 chirps and light flashes. Your
RPS Touch is now programmed.
Alarm rearm and lock
To rearm hold your finger on the ᴖRed Circleᴗfor 2.5 seconds.
Alarm disarm and unlock
To disarm hold your finger over the ᴖRed Circleᴗfor 2.5 seconds. Once the LEDs start their circular pattern, enter your 4 digit code. (Refer to Step 4 above.) Two
seconds after entering the 4th digit, your system will disarm.
rps@t@@rps@Hr @p@s I
By Firstech, LLC 24
Advanced System Functions
2 Way LCD remote paging
To page a 2 Way LCD remote just tap the ᴖRed Circleᴗtwice.
Touch Panel Sensitivity
To change touch sensitivity open the driverᴗs door, hold the button on the back of the RPS Touch until the LEDs go out. Release button and tap again. The number of solid
LEDs represent sensitivity of touch, 1 being the lowest, 5 the highest.
RPS (Remote Paging Sensor) Unlock/Disarm
RPS and car call functions do not require programming, however in order to unlock/disarm your vehicle you must program a 4 digit passcode using the instructions below:
STEP 1: Disarm/unlock the alarm (remote must be programmed first) and choose a 4 digit code. You can not have zeros.
STEP 2: Turn ignition key to the ᴘonᴙposition and leave the driverᴗs door open.
STEP 3: Knock on the windshield in front of the RPS a total of 5 times (each time you knock the LED on the RPS will flash RED). The LED will begin to flash rapidly in
BLUE with successful completion of this step.
STEP 4:Enter the first digit of the desired four digit pass code by knocking on the windshield in front of the RPS the desired number of times. For example, to enter 3, knock
on the sensor 3 times (each time you knock the LED will flash RED) then wait.
STEP 5: The LED on the RPS will confirm your first number by flashing BLUE slowly. Once the LED begins to flash rapidly in BLUE, enter your second number by
repeating step 4.
STEP 6:Repeat steps 4 & 5 to enter all four numbers.
STEP 7: Turn the ignition OFF - the RPS disarm/unlock passcode is now programmed. Follow steps 3 ? 5 to enter your disarm/unlock code.