Control input/output, Js-icon, Rx and js-icon – Johnson Systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1210/620) User Manual
Page 10: Tx wireless dmx is optional for all js-icon, Series dimmer racks. show dmx receiver (js-icon, Rx) and transmitter (js-icon, Products. the js-icon, Signal distribution board js-icon
10
J24
J23
J18
J17
J33
J30
J29
J28
J27
J26
J21
J20
J19
J16
J15
PS1
J1
J3
J2
J6
J4
J8
J7
J10
J9
J12
J5
J11
J14
J13
J32
INPUT
VAC
264
85
WATTS
15
DC
VOLTS
12
SUPPLY
POWER
T
O
AU
X
SCTY
FIR
E
OCOP
+12
V
COM
ANA4
ANA3
ANA2
ANA1
COM
B
C
N
CM
D-
D+
CM
D-
D+
CM
D-
D+
CM
D+
DMX A I/O
DMX B I/O
BUMP
REMOTE
LCD AND LED STATUS
D-
A
1+
1-
2+
2-
A-
B-
C-
D-
++
UAD
SSR1
UAD
SSR2
DUAL
SSR1
DUAL
SSR2
UAD
SSR3
FAN 1
FAN 2
-
1+
1-
2+
2-
A-
B-
C-
D-
++
1+
1-
2+
2-
A-
B-
C-
D-
++
1+
1-
2+
2-
A-
B-
C-
D-
++
1+
1-
2+
2-
A-
B-
C-
D-
++
1+
1-
2+
2-
A-
B-
C-
D-
++
T ERMO
TEMP
SENSOR
-STAT
LM35DT
+
-
FAN 3
FAN 4
+
-
UAD
SSR4
UAD
SSR5
UAD
SSR6
DUAL
SSR3
DUAL
SSR4
DUAL
SSR5
DUAL
SSR6
DUAL
SSR4
DUAL
SSR5
DUAL
SSR6
1210
62
0
N O
1+
1-
2+
2-
1+
1-
2+
2-
1+
1-
2+
2-
1210
62
0
1210
62
0
Signal Distribution Board
JS-ICON
™
Rx
MAINTAINED
NORMALLY OPEN
SWITCH CONTACT
+12V
ANA1-4
Control Input/Output
JS-ICON
™
Series dimmer racks come with a variety of control input and output
(I/O) capabilities. All I/O connections are terminated on the Signal Distribution
Board, located on the right-hand side of the dimmer rack.
Breakaway type connectors are supplied for all I/O connections.
• Use wire size #28 to #12 AWG. Strip insulation length to 0.3" (7.5mm).
• Torque terminations to 3.6 IN-LBS (0.4 NM).
NOTE: For connection use copper wire only, rated for 167°F (75°C) minimum.
Dual DMX Input and Through
• DMX A terminates to J7 and J8 connectors.
• DMX B terminates to J9 and J10 connectors.
• Complies with USITT DMX512-A (ANSI E1.11 - 2008), Standard protocol
for digital data control.
• Recommended cable is Belden 9829, 9842, Cat 5 or equivalent
(low-capacitance, twisted pair).
• Wiring must follow a daisy-chain topology.
• Maximum of 32 receiving devices on a single DMX line.
• Maximum cable length is 1,500 feet (455 meters).
• For more information, Google DMX, or visit:
NOTE: Ensure only the last (end-of-line) DMX receiving device is terminated!
Models JS-ICON
™
Rx and JS-ICON
™
Tx
Wireless DMX is optional for all JS-ICON
™
Series dimmer racks. SHoW DMX
receiver (JS-ICON
™
Rx) and transmitter (JS-ICON
™
Tx) is sourced from City
Theatrical, and has been selected for its reliability and ease of use. The JS-
ICON
™
Rx is specifically designed for easy adaptation to all JS-ICON
™
products.
The JS-ICON
™
Rx comes complete with a wiring harness and mounting
hardware. For more information visit:
+
12VDC Power Supply Output
• A regulated +12VDC power supply is available for powering external
devices.
• Terminate on +12V and COM of J12 connector.
• External devices should not exceed the maximum combined current draw
of 200mA.
0-10VDC Analog Inputs or Load Shed Contact Inputs
• Four (4) analog inputs terminate on J12 connector.
• AN1=Analog Input 1, AN2=Analog Input 2, AN3=Analog Input 3,
AN4=Analog Input 4.
• Inputs can be configured for normal or load shed mode of operation.
• Inputs can be patched to any combination of dimmer output circuits.
• Programmed in the “ANA MODE” and “ANA PTCH” menus. See page 22 for details.