Johnson Systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1210/620) - Manual (Page 24)

www.johnsonsystems.com 24
A+D< 001 Displays the active trigger mode as analog and DMX (A+D<) channel 001.
A+D> 001 Press EXECUTE to toggle the pointer (>) and select the DMX channel.
A+D> 512 Press MENU ( ) to change and select the DMX channel from 001 to 512.
A+D< 512 Press EXECUTE to toggle the pointer (<) and select a different trigger mode.
DMX< 512 Press MENU ( ) to select DMX input trigger mode.
ANA< Press MENU ( ) to select analog (ANA) input trigger mode.
OFF< Press MENU ( ) to deactivate (OFF) the open collector output.
Press ESCAPE to exit the menu and save the desired settings.
Press RESET to exit the menu without saving.
The menu will automatically timeout after 2 minutes of inactivity and save.
27. AUX IN Select which scene the auxiliary input will trigger/enable.
When a contact is sensed on the auxiliary input the selected scene will be triggered
and held until the contact is removed. The auxiliary input only functions when scene
mode (SCENESET) is activated or when the systems local buttons (L-BUTTONS) are
set for scene mode.
SCENE:01 Displays the scene (01) that will be triggered by the auxiliary input.
SCENE>01 Press EXECUTE to enter the menu and select a different scene.
SCENE>24 Press MENU ( ) to change the selected scene from 01 to 24.
Press ESCAPE to exit the menu and save the desired scene to be triggered.
Press RESET to exit the menu without saving.
The menu will automatically timeout after 2 minutes of inactivity and save.
28. L-BUTTON Set the mode of the local buttons to scene, bump or disabled.
JS-ICON ™ Series dimmer racks normally have the local buttons disabled. Bump mode
is used in conjunction with 24 bump button switches, not applicable with JS-ICON ™
Series dimmer racks.
Setting the local buttons to scene mode puts the system in scene mode. With scene
mode enabled, the selected scene will always be activated when DMX is not being
received. The selected scene can be changed in the SCENESET menu. Scene mode
enables the use of the auxiliary (AUX) input. A contact closure sensed on the over-
temperature (O/T), fire alarm (FIRE) or security alarm (SCTY) input automatically
takes precedence over scene mode.
DISABLED Press EXECUTE to toggle the operation of the local buttons to disabled.
BUMP Press EXECUTE to toggle the operation of the local buttons to bump mode.
SCENE Press EXECUTE to toggle the operation of the local buttons to scene mode.
Any change in the configuration is automatically saved.
29. S-ALARM Select the level and control channels triggered by the security alarm input.
When a contact is sensed on the security alarm input, selected control channels will
cycle on and off at a 1 hertz rate. The level of the on cycle can be set from 0% to
100%. The security alarm input takes precedence over the DMX and analog inputs.
The system will stay in security alarm mode until the contact is removed.
Press EXECUTE to enter the menu and configure the security alarm input.
L>FL:01* Displays the output level (L>FL) of 100% and control channel (01*).
L>00:01* Press MENU ( ) to change the output level from 00% to 100% (FL).
L>FL:01* Press MENU ( ) at the same time to toggle the level back to 100% (FL).
L:FL>01* Press EXECUTE to toggle the pointer (>) and select the control channel(s).
L:FL>24* Press MENU ( ) to select the desired control channel from 01 to 24.
L:FL>24 Press EXECUTE to toggle the flag (*) for each desired control channel.
Press ESCAPE to exit the menu and save the desired settings.
Press RESET to exit the menu without saving.
The menu will automatically timeout after 2 minutes of inactivity and save.