Document Outline

• Important User Information
• Additional Resources
• Chapter 1
  • Introduction
    • Safety Considerations
• Chapter 2
  • Installation
    • Installation Check List
    • Inspecting and Unpacking
    • Location (Environment)
    • System Components
    • Floor Mounting
      • Figure 1 - Bottom View Floor Mount Dimensions
    • Clearance
    • Circuit Breaker Recommendations
      • Table 1 - Recommended Branch Circuit Protection
    • Electrical Terminations
    • Accessing Terminations
      • Figure 2 - Top Conductor Entry
    • 3-Wire vs. 4-Wire Configurations
    • 3- Wire Models
      • Figure 3 - HC-DySC 3-Wire Configuration
    • 4- Wire Models
      • Figure 4 - HC-DySC 4-Wire Configuration.
    • Electrical Terminations and Ratings
      • Figure 5 - Electrical Terminations
• Chapter 3
  • Communications
    • Dry Contacts
      • Figure 6 - Access Cover Location
    • Serial Communications Port
      • Figure 7 - Serial Communications Port
• Chapter 4
  • Applying Power and Operation
    • Applying Power
    • HC-DySC System Operation
    • System Description
      • Figure 8 - One Line Diagram of the HC-DySC System
    • Maintenance Bypass Operation
    • Bypass Switch Modes
      • Figure 9 - Bypass Switch and Mode Operations.
    • Maintenance Bypass Transfer Procedure
      • Manual transfer to Bypass (maintenance) mode:
        • 1. Rotate bypass switch to the Test position, then to the Bypass position.
        • 2. Verify the screen on the HC-DySC displays “System Offline” in the upper left-hand corner of the home page.
        • 3. The HC-DySC is now bypassed and isolated for maintenance.
      • Manual transfer to Normal (sag protection) mode:
        • 1. Rotate CBI handle to the off/reset position then to the on position. Note: HC-DySC prevents re-closure of CBI within 1 minute of opening.
        • 2. Rotate the bypass switch to the Test position. ATTENTION: The bypass contacts are all timed to make-before-break and will not disrupt power to the load during any mode transitions. The switch has lockout/tagout (LOTO) provisions. Delay one second ...
        • 3. Verify the screen on the HC-DySC displays “OK” in the upper left-hand corner of the home page.
        • 4. Rotate the bypass switch to the Normal position.
        • 5. The HC-DySC system is now providing power to the load.
    • Operating and Alarm Modes
      • Table 2 - Operational Conditions and Indications
• Chapter 5
  • Display Screen
    • Overview
      • At installation time perform the following steps to configure your system:
        • Figure 10 - Home Screen
        • Figure 11 - System Configuration
        • Figure 12 - Touch Screen Calibration
        • Figure 13 - Set System Date and Time
    • Home Screen
      • Figure 14 - Home Screen
      • Table 3 - Home Screen Description
      • Mechanical Bypass
        • Figure 15 - Home Screen Mechanical Bypass
    • System Status
      • Figure 16 - System Status Summary
      • Figure 17 - - System Status Waveforms
      • Table 4 - System Status Description
      • Figure 18 - Status Screen Bypass Status
    • Voltage Sag Events
      • Voltage Sag Log
        • Figure 19 - Voltage Sag Log
        • Table 5 - Voltage Sag Log Description
    • Voltage Sag Detail
      • Figure 20 - Voltage Sag Detail
      • Table 6 - Voltage Sag Detail Description
    • Voltage Sag RMS Voltage Charts
      • Figure 21 - RMS Voltage Charts
    • Voltage Sag Notification
      • Figure 22 - Voltage Sag Detected
    • System Events
      • Table 7 - System Event Description
      • Informational
      • Auto-Resetting
      • User Attention
      • Manual-Reset
      • Call Service
      • System Event Log
        • Figure 23 - System Event Log
        • Table 8 - System Event Log Description
    • System Event Detail
      • Figure 24 - System Event Detail
      • Table 9 - System Event Detail
      • System Event Notification
        • Figure 25 - System Fault Detection
        • Figure 26 - System Fault Detection - Cleared
    • System Configuration
      • Figure 27 - System Configuration
    • Model Information
      • Figure 28 - Model Information
      • Table 10 - Model Information
      • Run System Tests
        • Figure 29 - System Tests
      • Diagnostics Mode
• Chapter 6
  • Maintenance
    • Preventative Maintenance
      • Monthly Checks
      • 3-6 Month Checks
        • Table 11 - System Event Table
      • POWER_ON
      • Informational
      • Unit
      • T_FAN_ST
      • Informational
      • Unit
      • T_IN_ST_1
      • Informational
      • Unit
      • T_IN_ST_2
      • Informational
      • Unit
      • T_IN_ST_3
      • Informational
      • Unit
      • EXTERNAL
      • Auto-Resetting
      • Inverter
      • RUN_TO
      • Auto-Resetting
      • Inverter
      • LIM_CYCLE
      • Auto-Resetting
      • Inverter
      • STAT_OT
      • User Attention
      • Static Switch
      • OVERLOAD
      • User Attention
      • Unit
      • DC_OV
      • User Attention
      • Inverter
      • CNTRL_UV
      • User Attention
      • Inverter
      • OUTPUT_UV
      • User Attention
      • Inverter
      • INV_OC
      • User Attention
      • Inverter
      • DC_UV
      • User Attention
      • Inverter
      • OUTPUT_OV
      • Call Service
      • Inverter
      • SYNC_ERR
      • Call Service
      • Inverter
      • CONFIG
      • Call Service
      • Inverter
      • CNTRL_MEM
      • Auto-Resetting
      • Inverter
      • UNBALANCE
      • Call Service
      • Inverter
      • AC_V_CHK
      • Call Service
      • Inverter
      • ROLL_CALL
      • Call Service
      • Unit
      • COM_VER
      • Call Service
      • Unit
      • CNFG_TO
      • Call Service
      • Unit
      • CNFG_ERR
      • Call Service
      • Unit
      • FIRM_TO
      • Call Service
      • Unit
      • FIRM_DIFF
      • Call Service
      • Unit
      • SRL_TO
      • Call Service
      • Unit
      • SRL_DIFF
      • Informational
      • Unit
      • T_INV_TO
      • Call Service
      • Unit
    • Servicing
      • Circuit Breaker CBI, Safety Interlocks and Stored Energy
      • Circuit Breaker CBA and Fuses
        • Fuse Rating Charts
          • Table 12 - HC-DySC Enclosure Fuses
      • Transient Voltage Surge Suppressor (TVSS)
• Chapter 7
  • Specifications and Dimensions
    • Table 13 - Technical Specifications 200 A HC-DySC
    • Table 14 - Heat Dissipation
    • Approximate Dimensions
      • Figure 30 - 200 A HC-DySC Dimensions