Soleus GPS Fit (SG100) - Manual (Page 3)

GPS Fit
CG12
GPS signals and its meaning:
Step 5) Go for a Run:
5.1) Using Run mode:
5.1.1) Press S7 or S1 from Time mode to go to RUN mode. The watch will display
GPS/INDOOR.
5.1.2) Press S1/S11 to select between GPS and INDOOR.
5.1.3) Press S5 to confirm selection. If you select INDOOR, you will have your exercise
without GPS data. If you select GPS, the watch will start searching for GPS signal;
display the battery level, remaining Memory, and the GPS GO screen.
5.1.4) Press S5 to change the views in ROW 1. Following are the views as you press S5:
o Chrono / GPS GO
o Pace / Distance / Chrono
o Speed / Distance / Chrono
o Calorie / Distance / Chrono
o Clock / Distance / Chrono
o Chrono / Distance / Chrono
o Distance / Distance / Chrono
5.1.5) Press and hold S5 to change the views in ROW 2. Following are the views as you
press & hold S5:
o Pace / Distance / Chrono
o Pace / Pace / Chrono
o Pace / Speed / Chrono
o Pace / Calorie / Chrono
o Pace / Clock / Chrono
o Pace / Chrono / Chrono
5.1.6) Press S1 to start. If auto lap function is set, the watch will take lap automatically
based on auto lap setting and there is a beep sound during taking of auto lap if
the ALERT is ON in AUTO LAP setting.
5.1.7) Press S1 to stop after completing your run.
5.1.8) While the chronograph is stopped, press S5 to view your current data before
saving. Following are the views as you press S5:
o Stop / Chrono / Distance
o Calorie / Ave Pace / Max Pace
o Calorie / Ave Speed / Max Speed
5.1.9) Press and hold S1 or press S11 to save your data.
Note: When the chronograph is stopped or reset, after 15 minutes if no key operation, the
GPS will automatically turn OFF and return to time mode.
RUN setting mode:
You can set the AUTO LAP/ UNIT/ and USER in RUN mode. You can also do this setting in
SET mode.
•
Press and hold S11 until AUTO LAP blinks.
• Press S1/S11 to toggle through between AUTO LAP, UNIT, and USER.
o AUTO LAP setting in RUN mode:
Ø Press S5 while AUTO LAP is blinking. Auto lap 1 will start to blink.
Ø Press S1/S11 to change the setting. Auto lap preset settings are: 0.4, 1, 2, 3, 4, and
5 KM.
Ø Press S5 to confirm and set ALERT ON or OFF.
Ø Press S1/S11 to change the setting. There is a beep sound and EL on for 10 sec
every auto lap taking when ALERT is set to ON.
Ø Press S5 to confirm setting and go back to Auto lap setting screen.
o UNIT setting in RUN mode:
Ø Press S5 while UNIT is blinking. KM will start to blink.
Ø Press S1/S11 to change the unit.
Ø Press S5/S7 to confirm setting and go back to UNIT setting screen.
o USER setting in RUN mode:
Ø Press S5 while USER is blinking. MALE will start to blink.
Ø Press S1/S11 to change the gender.
Ø Press S5 to confirm and set the AGE. Age digits will start to blink.
Ø Press S1/S11 to change the age digits.
Ø Press S5 to confirm and set the WEIGHT. Weight digits will start to blink.
Ø Press S1/S11 to change the weight digits.
Ø Press S5 to confirm and set the HEIGHT. Height digits will start to blink.
Ø Press S1/S11 to change the height digits.
Ø Press S5 to confirm and go back to USER setting screen.
Ø Press S7 to exit