Panasonic PV-7451 - Manual (Page 25)

In order tor the VCR to read the VCR Plus+ code, some set up is required. A Guide (VCR Plus+) channel number is assigned to
each local broadcast and cable station. Because this number sometimes differs from the channel your TV receives the station
on, it is necessary to program the VCR with local channel information.
VCR Plus+ Channel Setup
For Connection Type B (page 24) only
■ Before you begin, complete the Channel Setup
Preparations below left.
Important Note:
If your VCR connection type changes from type A to B, repeat
steps 1-^ of page 24 and select VCR^CABLE/DSS BOX^TV
or VCR^TV before proceeding with these steps.
■ Push MENU to
O display the menu.
Channel Setup Preparations
NOTE: Complete the steps on this page if your
VCR hook-up resembles “B" on page 24.
Prepare a list like the example below.
This list will help you smoothly enter the
information needed in step “d" at right.
You will need the following to complete the list:
H A line up of normal and/or cable stations you
receive along with the channel numbers your
TV receives them on. A cable channel line-up
chart is supplied by your cable company.
H A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in TV
Guide and the TV listings found
in selected newspapers.
i Make a chart with 3 columns like the example
' below. In the left column, fill in the name or call
letters of the stations you receive.
O In the middle column, fill in each station’s
assigned Guide (VCR Plus+) number found in
TV Guide, newspapers, etc.
O In the right column, fill in the channel number
** that your TV receives the station on from your
channel line-up.
EXAMPLE ONLY
Broadcast or Cable
Station Name
Assigned
Guide
(VCR Pius+)
channei no.
Channei no.
your TV
receives the
station on
HBO 33 15
Nickelodeon 38 20
CBS 04 04
FOX 11
.................. MENU -------------
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE:ENGLISH
SELECT : A T KEY
SET :► KEY
END :MENU KEY Push
AW
to select
“SET UP CHANNEL,”
and then push ► to display
the “SET UP CHANNEL” screen.
Push
AT
to select
“VCR Plus+ CH SET
UP,” and then push ►
to display the “VCR
Plus+CHSETUP”
screen.
--- SET UP CHANNEL ---
ANTENNA SYSTEM : CATV
AUTO SET
CABLE/DSS BOX SET UP
VCR PIUS+ CH SET UP
SELECT:A T KEY
SET :► KEY
END :MENU KEY
IMPORTANT NOTE:
For step “d,” use the list you prepared. You may leave lines
blank if you don’t receive that station, or if the GUIDE CH
number and the CATV (or TV) CH numbers are the same.
f Push ► to move
i the shaded area to
I
the right side.
Then, push AT to change CATV
or TV CH number.
Next, push 4 to set the number.
Now, push AT to continue.
Repeat this operation until the list is
complete.
VCR PIUS+ CH SET UP
GUIDE CH CATV CH
► sn
02
SELECT
SET
END
A ▼ KEY
► KEY
MENU KEY
VCR Plus+ CH SET UP
GUIDE CH CATV CH
► 01
02
SELECT: A T KEY
SET : - 4 K E Y
END :MENU KEY
To Make Corrections
Push AT and ► to select the incorrect CATV or TV CH number.
Then, push AT to change, or ADD/DLT to delete the channel.
O
Push MENU three times
to exit the VCR Plus+ CH
SET UP mode.
Make each entry within 5 minutes or the VCR will leave this mode.
Once local channels have been programmed, they will stay in
memory, even in the case of a power failure.
VCR Plus+ and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ system is manufactured
under license from Gemstar Development Corporation.
25