Chamberlain door opener - Manual (Page 19)

19
3-BUTTON REMOTE CONTROLS
Your 315MHz Security✚ ® or dip switch remote control can be
programmed to operate as a 3-button wireless control station:
the large button will open the door, the middle button will
close the door, and the third button will stop the door’s
movement. You may set up this feature as follows:
1. To enter programming press the RADIO button on the logic
board (the RADIO LED will light).
2. To program the OPEN button to a remote control press the
OPEN button on the logic board. The RADIO LED will flash and
then stay on solid. Then press the corresponding button on the
remote control. The RADIO LED on the logic board will flash,
this confirms that the remote control has been programmed.
(By programming the remote control you use 1 channel of the
23 channels on the radio receiver.)
3. To program the CLOSE button to a remote control press the
CLOSE button on the logic board. The RADIO LED will flash
and then stay on solid. Then press the corresponding button
on the remote control. The RADIO LED on the logic board will
flash, this confirms that the remote control has been
programmed. (By programming the remote control you use 1
channel of the 23 channels on the radio receiver.)
4. To program the STOP button to a remote control, press the
STOP button on the logic board. The RADIO LED will flash and
then stay on solid. Then press the corresponding button on the
remote control. The RADIO LED on the logic board will flash,
this confirms that the remote control has been programmed.
(By programming the remote control you use 1 channel of the
23 channels on the radio receiver.)
5. After learning remote controls press the RADIO button on the
logic board (LED will turn off). NOTE: If no activity within 30
seconds the radio will automatically exit programming mode.
OPEN
CLOSE
STOP
U1
POWER
TIMER DEFEAT
MAS
4
MRT
1 RADIO
MID
2
TIMER
TIMER
ENABLE
T TS
FSTS E2
RELAY A
RELAY B
D1 DIAG
C2
B2 PROG
3
24V
AC
24V
AC
TIMER
DEFEAT
CMN
MAS
EYES
EDGE
OPEN
CLOSE
STOP
CMN
SBC
11
10
9
14
13
12
8
7
6
5
4
3
2
1
CLOSE
STOP
OPEN EDGE
OLS
MID
SLS
M OTO
R
DIRECTION
REV STD
CLS
D25
D24
D26
D27
D36
C77
C73 C54
C78
L1
L5
P6
D35
S8
D16
P7
EYES
K3
P1
D34 F1
FAILSAFE (B2 C2 D1 E2)
NON FAILSAFE
D23
D15 D1
D22
R8
J1
X1
E1
R29
C18
D8
U7
R31
D31
C3Ø
D7
D6
D5
D4 C25 C17
C11
D3Ø2 P1Ø
P4
Ø14LGØ657–A Ø14GPØ657–A
J3ØØ
D2Ø
D21
D13
D14
D28
D17
D19
CONT
A CT
OR/3 PH
SINGLE PHASE
SBC C71
®
CLOSE
STOP
OPEN
EDGE D1
D22
D2Ø
D21
D13
Open
Close
Stop
REMOTE CONTROL PROGRAMMING FEATURE
Program Remote Controls from the 3-button control station
(3BCS).
Requires Firmware Version 4.6 or higher and a 3BCS with the
MAS connected to the control board.
This feature allows the user to add additional remote controls from
the 3BCS. By default the remote control learn option is off.
NOTE: Requires access to the operator electrical box to enable or
disable this feature.
To turn this feature on:
1. Turn the SELECTOR DIAL to PROG.
2. Press and release the RADIO button. The RADIO LED will be lit.
3. Press and release the MID button. The RADIO LED will flash
quickly 6 times.
4. Press and release the RADIO button. The RADIO LED will turn
off.
5. Return the SECTOR DIAL to the desired wiring type.
To add remote controls from the 3BCS:
1. With the door in the fully closed position (close limit activated),
press and hold STOP.
2. While holding STOP, press and hold CLOSE.
3. While holding STOP and CLOSE, press and hold OPEN.
4. Release all three buttons once the MAS LED has lit.
5. Learn a remote control by one of the following methods:
a. Programming a standard single button/single function
remote control, push and hold the remote control button
until the MAS LED goes out. Repeat steps 1 through 4 to
add additional remote controls.
b. Programming a 3-button/three function remote control
(open/close/stop), first push the button on the 3BCS
(example: OPEN) and then press and hold the button on the
remote control (example: large button) that you want to
correspond with the selected (example: OPEN) command
until the MAS LED flashes and goes out. Repeat steps 1
through 4 to add additional buttons (close and stop).
To turn this feature off:
1. Turn the SECTOR DIAL to PROG.
2. Press and release the RADIO button. The RADIO LED will be lit.
3. Press and release the MRT button. The RADIO LED will flash
quickly 3 times.
4. Press and release RADIO button. The RADIO LED will turn off.
5. Return SELECTOR DIAL to desired wiring type.
NOTE: Restoring the operator to Factory Default (see “RESETTING
FACTORY DEFAULTS”) will also disable this feature. The remote
controls will still be learned.
P R O G R A M M I N G