Campbell Hausfeld AT122601 - Manual (Page 2)

(like a wooden pallet) a dry mat, or dry
carpet.
GeneRal SaFeTy
• . Read .all .manuals .included .
with .this .product .carefully . .
Be .thoroughly .familiar .
with .the .controls .and .the .
proper .use .of .the .equipment . .Follow .
all .instructions .
• . Only .persons .well .acquainted .with .
these .rules .of .safe .operation .should .
be .allowed .to .use .the .unit .
Do not
misuse
this product. Excessive exposure to
vibration, work in awkward positions,
and repetitive work motions can cause
injury to hands and arms. Stop using
any tool if discomfort, numbness,
tingling or pain occur, and consult a
physician.
1 . . Read .this .instruction .manual .before .
connecting .this .device .to .the .
compressor .
2 . . Safety .glasses .or .face .shield, .gloves .
and .a .NIOSH .approved .respirator .
must .be .worn .during .operation . .
Always .work .in .a .well .ventilated .
area .
3 . . During .operation, .do .not .expose .the .
hands .or .skin .directly .in .the .line .of .
the .blast .nozzle .
4 . . After .installation, .inspect .to .make .
sure .all .components .seal .properly .
5 . . Keep .children .away .at .all .times . .All .
visitors .must .be .kept .a .safe .distance .
and .wear .safety .glasses, .gloves .and .a .
respirator .
6 . . Do .not .exceed .the .maximum .
operating .pressure .of .the .
sandblasting .equipment .(125 .psi) .
MANUAL
Disconnect the sandblaster from the air
supply before changing accessories or
attempting to install, service, relocate
or perform any maintenance.
7 . . Check .hoses .and .air .lines .for .weak .
or .worn .condition .before .each .use . .
Make .sure .all .connections .are .secure .
before .use .
Do not
point
the sandblast gun at anyone or objects
other than the intended work object.
8 . . Do .not .depress .the .trigger .when .
connecting .the .air .supply .hose .
Do not
work
around oily rags or flammable liquids.
Sand striking metal can cause a spark
and create a fire or explosion.
Do not
spray
acids or caustics.
assembly
MoDel aT122601
1 . . Attach .material .hose .to .the .pick-up .
tube . .Place .pick-up .tube .in .bag .of .
medium . .(See .FIgure .4) .
2 . . Attach .the .air .compressor .hose .
to .the .air .inlet .(1/4 .inch .NPT(F)) .
at .the .bottom .of .the .gun .handle . .
An .optional .quick .coupler .and .
2
Operating .Instructions
www.chpower.com
General Safety Information
(Continued)
connector .can .be .used .to .attach .the .
hose .to .the .gun .
MoDel aT125102
1 . . Attach .the .material .hose .to .the .hose .
connector . .Attach .the .opposite .end .
of .the .material .hose .to .the .gun .(See .
Figure .5) . .Never .use .hose .clamps .to .
secure .the .hose .
noTe: .Do .not .cover .the .hole .in .the .
hose .connector .for .dry .blasting . . .For .
spraying .liquids, .slip .the .material .hose .
fully .on .to .the .hose .connector .covering .
the .hole .
2 . . Attach .the .air .compressor .hose .
to .the .air .inlet .(1/4 .inch .NPT(F)) .
at .the .bottom .of .the .gun .handle . .
An .optional .quick .coupler .and .
connector .can .be .used .to .attach .the .
hose .to .the .gun .
MoDel aT121002
1 . . Attach .the .hose .connector .to .the .
hopper .using .the .supplied .conduit .
nut .
2 . . Attach .the .material .hose .to .the .hose .
connector . .Attach .the .opposite .end .
of .the .material .hose .to .the .gun .(See .
Figure 1
Figure 2
Figure 3
Figure 5 - Model aT125102
Figure 4 - Model aT122601
Attach .air .
hose Material .
hose
Do .not .cover .outer .
tube .with .hose .for .dry .
blasting
Pick-up .tube