Kenmore 153.337613 - Manual (Page 24)

Troubleshooting Guide (cont*d)
Start Up Conditions (cont’d)
CONDENSATION
Whenever the water heater is filled with cold water, a certain
amount of condensation will form while the burner is on. A
water heater may appear to be leaking when in fact the water is
condensation. This usually happens vmen:
• When a new water heater is filled with cold water for the
first time.
• When gas burns and water vapor is produced in water
heaters, particularly high efficiency models where flue tem^
peratures are lower,
• When you use large amounts of hot water in a short time
and the refill water is very cold.
Moisture from the products of combustion condense on the
cooler tank surfaces and form drops of water which may fall
onto the burnet or other hot surfeces to produce a “sizzling” or
“frying” noise.
Excessive condensation can cause pilot outage due to water run­
ning down the flue tube onto the main burner and putting out
the pilot.
Because of the suddenness and amount of water, condensation
water may be diagnosed as a “tank leak”. After the water in the
tank warms up (about 1-2 hours), the condition should
disappear.
Do not ^sume the water heater is leaking until there has been
enough time for the water in the tank to warm up.
An undersized water heater will cause more condensation. The
water heater must be sized properly to meet the family’s
demands for hot water including dishwashers, washing machines
and shower heads.
Excessive condensation may be noticed during the winter and
early spring months when incoming water temperatures are at
their lowest.
Good venting is essential for a gas fired water heater to operate
properly as well as to carry away products of combustion and
■ water vapor.
SMOKE/ODOR
It is not uncommon to experience a small amount of smoke and
odor during the initial start-up. This is due to burning off of oil
from metal parts, and will disappear in a short while.
Operational Conditions
SMELLY WATER
In each glasslined water heater there is installed at least one
anode rod (see parts section) for corrosion protection of the
tank. Certain water conditions will cause a reaction between this
rod and the water. The most common complaint associated with
the anode rod is one of a “rotten egg smell”. This odor is derived
from hydrogen sulfide gas dissolved in the water. The smell is
the result of four faaors which must all be present for the odor
to develop:
a. a concencration of sulfate in the supply water,
b. little or no dissolved oxygen in the water.
c. a sulfate reducing bacteria within the water heater. (This
harmless bacteria is non-toxic to humans.)
d. an excess of active hydrogen in the tank. This is caused by
the corrosion protective action of the anode.
Smelly water may be eliminated or reduced in some water heater
j the anode(s) with one of less active material,
and then chlorinating the water heater tank and all hot water
lines. Contact Sears Service for further information concerning
an Anode Replacement Kit #9001453 and this Chlorination
Treatment,
If the smelly water persists after the anode replacement and chlo­
rination treatment, we can only suggest that continuous chlori­
nation and filtering conditioning equipment be considered to
eliminate the water problem.
Do not remove the anode leaving the tank unprotected. By
doing so, all warranty on the water heater
tank ¡$ voided.
awarning
HOTTER WATER CAN SCALD: Wrter heaters are intended to
pn^uce hot water. Water heated to a temperature which will
satisfy dotiies washing, dish washing, and other sanitizing needs
can scald and permanently injure you upon contact Some peo­
ple are more likely to be permanently injured by hot water than
others. These indude the elderly, children, the infirm, or physical-
ly/fn«itally handicapped, if anyone using hot water in your home
(its into one of these ^nnips or if there is a local code or law
requiring a certain ^pwature water at the hot water tap, then
you must take spedai precautions. In addition to using the lowest
possible temperature setting that satisfies your hot water needs,
a means such as a mixing valve, should be used at the hot water
taps us^ by these people or at the vrater heater. Mixing valves
are available at plumbing supply or hardware stores. Follow man­
ufacturers instructions for installation of the valves. Before
changing the factory setting on the thermostat, read the
Temperature Regulation” section in this manual.
‘AIR" IN HOT WATER FAUCETS
awarning
HYDROGEN GAS: Hydrogen gas can be produced in a hot
water system that has not been used for a long period of time
(generally two vreeks or more). Hydrogen gas is extremely
flammable and e^losive. To prevent the possibility of injury
under these conditions, we recommend the hot water hujcet
be opmed for several minutes at the kitdten sink before any
electrical appliances which are connected to the hot water sys­
tem are used (such as a dishwasher or washing machine). If
hydrogen gas Is present, there will probity be an unusual
sound »milar to air escaping through the pipe as the hot water
foucet is opened. There must be no smoking or open flame
near the faucet at the time it is open.
24