Inteli•touch – Casablanca Fan Company Casablanca Ceiling Fan 6643050 User Manual

Page 10

Advertising
background image

10

Inteli•Touch

R

R

Programmed into every Inteli-Touch Series fan is an Automatic
Demonstration Program. It can be used to fully demonstrate and
test the operation of the fan.
To enter the demonstration program:

1. Turn

POWER off for at least three seconds. This will clear

the fan memory ready for programming.

2. Turn

POWER on.

3. Immediately operate the buttons in the following sequence:

A multi-tone signal will verify the start of the test program which
proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short time).
• Lights turn off.

The complete cycle lasts slightly over one minute. It will continue
to repeat until the

POWER is turned off for more than three

seconds, cancelling the program.

The

POWER button is normally left in the on position. Always turn the power off

during cleaning or servicing the fan and during thunderstorms. It is also used to
exit or enter additional programs.

POWER must be left on to retain a previously set fan speed or light level.

There are six individual speed settings for the fan; each speed is indicated
by an audible tone of increasing pitch.
To select the desired fan speed:

1. With fan off, press and hold the button labeled

. The fan blades

will start rotating at the slowest speed, and will increase in steps.

2. Release the button when the desired speed is reached.

The fan speed is now in memory and will automatically come on at the same
speed each time the

button is used. To maintain this level of speed,

turn the fan on by pressing

less than one second. To lower speed,

turn fan off, then on by pressing and holding the

button until the

desired speed is reached. When the fan is on, you may increase the speed by
pressing and holding the

button until the desired speed is reached,

then release it.

The direction of airfl ow can be changed from downward to
upward or from upward to downward.

To reverse the airfl ow:

1. Make sure the

is on.

2. Press the

button.

Note: A four-toned signal indi-
cates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.

LIGHT CONTROL

ON - OFF

A momentary press of

the LIGHT button

TO CHANGE BRIGHT-

NESS

PRESS AND HOLD

LIGHT BUTTON

LONGER THAN ONE

SECOND

To turn the lights off and on, press and release the

button for less

than one second.

To vary the light brightness:

1. With lights off, press and hold the

button. After one second the

lights come on at their lowest level and gradually become brighter.

2. Release the button when the desired brightness level is reached.

The brightness level is now in the fan memory and will automatically come
on at the same brightness the next time the

button is used. To

maintain this level of brightness, press the

button for less than

one second. To lower the brightness, turn the lights off, then press and hold
the

button until the desired brightness level is reached. When the

light is on, you may increase the brightness level by pressing and holding
the

button until the desired level is reached, then release it.

FAN CONTROL

ON - OFF

A momentary press

of the FAN button

TO CHANGE SPEED

Press and hold FAN

button longer than

one second

INTELI•TOUCH OPERATION POWER

INTELI•TOUCH OPERATION SPEED CONTROL

INTELI•TOUCH • REVERSING AIRFLOW

INTELI•TOUCH LIGHT

AUTOMATIC DEMONSTRATION PROGRAM

FAN

+

+

+

+

+

+

+

+

LIGHT

FAN

LIGHT

FAN

FAN

LIGHT

FAN

FAN

FAN

FAN

FAN

REVERSE

LIGHT

LIGHT

LIGHT

LIGHT

LIGHT

R

POWER

POWER

POWER

R

Advertising