Futaba CGY750 - Manual (Page 23)

23
S WASH E XPERT S ETTING
7KHVZDVKH[SHUWPHQXFRQWDLQVVHWWLQJVIRUSLORWVORRNLQJWRDFKLHYHWKHDEVROXWHEHVWSHUIRUPDQFHIURPWKHLUJ\URE\SUHFLVHO\DGMXVWLQJVZDVK-
SODWHPRYHPHQWVRDVWRYLUWXDOO\HOLPLQDWHDGYHUVHÀLJKWEHKDYLRUGXULQJVRPHPDQHXYHUVVXFKDVUROORUORRSVÀLSV,WHPV  ±  DUHXVHGWR
NHHSWKHVZDVKSODWHOHYHODWKLJKDQGORZFROOHFWLYHSLWFKDQGWRUHGXFHRUHOLPLQDWH3,7
F\FOLFDQG$,/ (/(DQG(/( $,/F\FOLFH&&30
LQWHUDFWLRQV7RHQWHUWKH([SHUWPHQXQDYLJDWHWRWKH%DVLFPHQXSUHVVDQGKROGWKHPRGH>@NH\IRURQHVHFRQGDQGWKHPHQXZLOOFKDQJHIURP
WKH%DVLFWR([SHUW7RH[LWWKHH[SHUWPHQXSUHVVDQGKROGWKHPRGH>@NH\IRURQHVHFRQGDQGWKHEDVLFPHQXZLOOEHGLVSOD\HG
SWASH EXPERT
MAP 1/2
(1) Swash expert setting: start display
Use the mode [+] or [-] keys to navigate through the menu.
 3,7ĺ$,/PL[LQJUDWH>GHIDXOW @>UDQJHV a@
 3,7ĺ(/(PL[LQJUDWH>GHIDXOW @>UDQJHV a@
 $,/ĺ3,7PL[LQJUDWH>GHIDXOW @>UDQJHV a@
 $,/ĺ(/(PL[LQJUDWH>GHIDXOW @>UDQJHV a@
This parameter adjusts the aileron to 2nd elevator mixing rate. The rate can be adjusted for left
and right directions individually. It is only available for H4-45 swash mode. It is only available for
H4-45 swash mode.
 (/(ĺ(/(PL[LQJUDWH>GHIDXOW @>UDQJHV a@
This parameter adjusts the elevator to 2nd elevator mixing rate. The rate can be adjusted for up
and down directions individually. It is only available for H4 swash mode. It is only available for H4
swash mode.
  (/(ĺ3,7 PL[LQJ UDWH >GHIDXOW   +   H[FHSW + @ >UDQJHV   a
150%]
 (/(ĺ$,/ PL[LQJ UDWH >GHIDXOW   +   H[FHSW + @ >UDQJHV   a
150%]
(11) Linkage compensation aileron [default: 0%] [ranges: 0% ~ 100%]
 3,7ĺ(/(PL[LQJUDWH>GHIDXOW @>UDQJHV a@
This parameter adjusts the pitch to 2nd elevator mixing rate. The rates can both be adjusted indi-
vidually for both full high and low collective positions. It is only available at H4 swash mode.
 $,/ĺ(/(PL[LQJUDWH>GHIDXOW @>UDQJHV a@
This parameter adjusts the aileron to elevator mixing rate. The rate can be adjusted for left and
right directions individually. It is only available for H4-45 swash mode.
***Note: Items (2)-(15) and how to adjust are described in detail in the Linkage Compen-
sation Section that follows the Swash Expert Setting section.***
(12) Compensation direction of the aileron [default: plus]
(13) Linkage compensation elevator [default: 0%] [ranges: 0% ~ 100%]
(14) Compensation direction of the elevator [default: plus]
(15) Speed compensation [default: 50%(H3-120), 0%(except H3-120)] [ranges: 0% ~ 100%]
Push DATA
+/– key
Push DATA
+/– key
Push MODE
+/– key