Futaba CGY750 - Manual (Page 25)

25
*It does not display, when Opr.
mode is Gyro+THR, and when
SWASH-type is H4-00/H4-45.
*It does not display, when Opr.
mode is Gyro+THR, and when
SWASH-type is H4-00/H4-45.
*It does not display, when Opr.mode is
Gyro+THR, and when SWASH-type is
H4-00/H4-45.
*It does not display, when Opr.
mode is Gyro+THR, and when
SWASH-type is H4-00/H4-45.
*It does not display, when Opr.mode is
Gyro+THR, and when SWASH-type is
H4-00/H4-45.
*It does not display, when Opr.mode is
Gyro+THR, and when SWASH-type is
H4-00/H4-45.
G
OVERNOR
E
XPERT
S
ETTING
7KLVPHQXVHWVWKHGHWDLOVRIWKHJRYHUQRUIXQFWLRQIRUWKHH[SHUWPRGHOHU3XVKWKHPRGHRU±NH\IRUPRUHWKDQRQHVHFRQGRQWKH*RYHUQRU%DVLF
PHQXGLVSOD\WRJHWLQWRWKH*RYHUQRU([SHUWPHQX3XVKPRGHRU±NH\IRUPRUHWKDQRQHVHFRQGDJDLQRQWKH*RYHUQRU([SHUWPHQXWREHUH-
WXUQHGWRWKH*RYHUQRU%DVLFPHQX
GOVERNOR EXPERT
MAP 1/2
(1) Governor Expert setting: start display
Push mode + or – key, to scroll through the editing menu. Pushing mode + or – key for more than
one second, brings you back to governor basic menu.
(2) Governor working mode [default: Governor]
This parameter selects the governor working mode as either governor or revolution limit mode. The
governor mode works to actively maintain the engine’s revolution is at a constant rate. The revolu-
tion limit (Rev. Lmt) mode only works when the engine revolution exceeds the set RPM revolution
and engine revolution needs to be reduced. Pushing data+ or – key the mode is changed. When
the Rev.Lmt mode is selected, the menu (6) Throttle data mode should be set to Tx.Curve mode.
(3) Revolution display mode [default: Rotor]
This parameter selects the revolution display mode for either the main rotor or engine revolution.
By pushing data+ or – key, the mode is changed.
(4) Operation response [default: Middle]
This parameter selects the governor operation response. Select the best match for your engine
type. Pushing data+ or – key, the mode is changed. Recommended selection are, Middle
glow
engine, Moderate gasoline engine, Quick brushless motor, Silent electric models when
RPM detection is accomplished either with a magnet on the motor’s rotor or with a brushless
phase sensor.
(5) Governor gain [default: Moderate=30%,Middle=40%,Quick=60%] [ranges: 10% ~ 100%]
This parameter sets the governor working gain. When the operation response is changed, the
governor gain is automatically changed as default. The best gain percentage is the amount right
before engine RPM “hunting”occurs. By pushing the data+ or – key, the value is changed.
(7) Revolution change up delay [default: 8] [ranges: 2 ~ 20]
This parameter sets the delay of the rpm change from a lower setting to a higher one. By pushing
data+ or – key, the value is changed.
(8) Revolution down delay [default: 10] [ranges: 2 ~ 20]
This parameter sets the delay of the rpm change from higher setting to lower one. By pushing
data+ or – key, the value is changed.
(6) Throttle data mode [default: Optimize]
This parameter selects the throttle input operation. Pushing data+ or – key, the mode is changed.
Optimize:
&*<VHWVWKHWKURWWOHLQSXWVLJQDOWRRSWLPXP7KHUHLVQRQHHGWRFRQVLGHUWKHWKURWWOHFXUYHVHWWLQJ
RQWKHWUDQVPLWWHU
Fixed:
7KH¿[HGWKURWWOHLQSXWLVXWLOL]HGUHODWHGWRWKHUHYROXWLRQ,WLVUHFRPPHQGHGIRUHOHFWULFPRWRUV
Tx.Curve:
&*<XVHVWKHH[DFWWKURWWOHLQSXWIURPWKHWUDQVPLWWHU7KHWKURWWOHFXUYHVHWWLQJRQWKHWUDQVPLWWHULV
UHTXLUHG:KHQWKH5HY/PWPRGHLVVHOHFWHGWKLVPRGHVKRXOGEHVHOHFWHG
Push DATA
+/– key
Push DATA
+/– key
*It does not display, when Opr.
mode is Gyro+THR, and when
SWASH-type is H4-00/H4-45.
Push DATA
+/– key
Push DATA
+/– key
Push MODE
+/– key
(9) Start delay [default: 5] [ranges: 2 ~ 20]
This parameter sets the delay during the starting of the governor. By pushing data+ or – key, the
value is changed.
*It does not display, when Opr.mode is
Gyro+THR, and when SWASH-type is
H4-00/H4-45.