Canon Multimedia Projector LV-8235 UST - Manual (Page 7)

7
Immediately turn the power off, unplug the projector,
and contact your dealer under the following conditions,
otherwise a fire or an electric shock may result.
– If smoke comes out from it.
– If it emits a strange odor, or makes a strange
noise.
– If lamp goes out with a loud bang.
– If water or any other liquid gets into it.
– If metal or foreign objects get inside it.
– If it is knocked down or dropped and the cabinet is
broken.
WARNING
Follow the instructions below when using the power
cable, otherwise a fire, an electric shock, or injury may
result.
– Do not place heavy objects on the power cord or
position the power cord under the projector. Doing so
may damage the power cord.
– Do not run the power cord under a carpet. As it goes
unnoticed, excessive load may be applied on the cord
unintentionally.
– Do not modify, bend forcibly, twist, or pull the power
cord.
– Do not place the power cord near heat generating
equipment or heat it.
– Do not bend, wind, or bind excessively the power cord
when using it.
– Be sure to connect the projector to a grounded outlet.
Failure to do so may result in an electric shock.
– Do not continue to use a damaged power cord. If the
power cord is damaged, take it to your dealer and
have it replace.
– Use only the supplied power cord.
Follow the instructions below when handling the power
plug or connector, otherwise a fire, an electric shock, or
injury may result.
– Use the projector within the voltage range specified on
the projector (AC 100 V– 240 V).
– Insert the power plug or connector into the power
outlet firmly. Do not use a damaged or loosen power
plug or connector.
– Be sure to hold the power cord plug or connector
when disconnecting it from the power outlet. If the
power cord itself is pulled, it may be damaged.
– Do not plug or unplug the power cord with wet hands.
– Disconnect the power cord from the power outlet
before cleaning the projector.
– Do not stick metal objects into the electrical contacts
of the power plug or connector.
Follow the instructions below to install or handle the
projector. Otherwise, a fire, an electric shock, or injury
may result.
– Do not touch the projector, power cord, or cables when
lighting begins.
– Do not use the projector in a bathroom or shower
room.
– Do not expose the projector to rain, snow, or use near
water.
– Do not insert metal objects into the projector through
the air vents.
– Do not place the containers with water on the
projector.
– Do not install in the locations exposed to oily vapors or
smoke (e.g., near a cooking table or humidifier).
– Before moving the projector, turn the power off and
disconnect the power cord and all cables.
– Do not put spray cans in front of the exhaust vent.
When spray cans are exposed to heat, the pressure in
them will increase and explode.
– Do not open nor remove the cabinet. There are high
voltage components inside the projector. Contact your
dealer for inspection, adjustment, and service.
– Do not attempt to disassemble the projector (including
expendable parts) or remote controller.
– Do not look into the lens while the projector is used.
Strong light may hurt your eyes. Be especially careful
that small children do not look into the lens.
– When an extension cord is necessary, be sure that the
total current load of all equipment connected to the
extension cord does not exceed the specified rating of
the extension cord.
– Periodically unplug the power cord and remove the
dust that builds up on the power cord or connector.
Follow the instructions below when handling the
batteries. Failure to do so may cause explosion, heat
generation, a fire, or leakage of the battery fluid.
– Do not heat or disassemble the batteries, or throw
them into fire.
– Do not attempt to recharge the batteries.
Follow the instructions below when the lamp is replaced
or breaks.
– Always unplug the power cord before replacing the
lamp.
– When the lamp breaks, shards of glass may scatter in
the lamp housing. Contact your dealer for cleaning or
inspecting the projector, or replacing the lamp.
WARNING
WARNING
WARNING
WARNING
WARNING
Safety Instructions