Scientech S310 Vector - Manual (Page 19)

19
3. To Zero the Analog Needle (does not apply to the S310D):
Refer to Figure 3. The black slotted button located just below the display allows screwdriver adjustment to set
the analog needle to zero. This adjustment should be made before connecting a pyroelectric detector.
4. To Connect a Pyroelectric Detector:
Note: Only one detector should be plugged in at any time.
Refer to the drawing of the S310 rear panel in Figure 2. A 3 meter BNC type cable comes with Vector
pyroelectric detectors and Vector HR pyroelectric detectors. One of the input connectors on the rear panel of
the S310 is labeled "Vector" for hook up of the pyroelectric detectors.
5. To Select a Group:
A. Press the SETUP button. The Group Setting last used will appear in the display.
B. To move to the next Group, press SETUP button again.
C. To select the appropriate Group, press the SELECT button when the Group you desire appears in the
display (failure to press the SELECT button within 3 seconds will activate the Group shown in the
display and return the S310 to its operational state).
6. To Select a Range:
Note: AUTO range may be selected if the energy levels of repetitive pulses are to be measured.
However, do not select AUTO range if you want to measure single pulse energy or pulses
running at repetition rates lower than 10 Hz.
A. Press the RANGE button. On the first press of the RANGE button, the analog scale (if active) will
disappear. Then briefly press the RANGE button each time another range is desired.
B. To select a range, press the SELECT button when the range you desire appears in the display (failure to
press the SELECT button within 3 seconds will activate the range shown in the display and return the
S310 to its operational state). The ranges available for pyroelectric detectors are in the following table.
Model Standard or SP PHF02 - L PHF02 – S or I PHF05 – L PHF05 – S or I
Mode Power Energy Power Energy Power Energy Power Energy Power Energy
Ranges
3mW
30mW
300mW
3W
AUTO
3mJ
30mJ
300mJ
3J
AUTO
30.00µW
3.000µW
3.000mW
30.00mW
AUTO
30.00µJ
3.000µJ
3.000mJ
30.00mJ
AUTO
3.000µW
30.00µW
300.0µW
3.000mW
30.00mW
AUTO
3.000µJ
30.00µJ
300.0µJ
3.000mJ
30.00mJ
AUTO
300.0µW
3.000mW
30.00mW
AUTO
300.0µJ
3.000mJ
30.00mJ
AUTO
3.000µW
30.00µW
300.0µW
3.000mW
30.00mW
AUTO
3.000µJ
30.00µJ
300.0µJ
3.000mJ
30.00mJ
AUTO
Model PHF09 – L PHF09 – S or I P05 P09
Mode Power Energy Power Energy Power Energy Power Energy
Ranges
3.000mW
30.00mW
AUTO
3.000mJ
30.00mJ
AUTO
30.00µW
300.0µW
3.000mW
30.00mW
AUTO
30.00µJ
300.0µJ
3.000mJ
30.00mJ
AUTO
3.000µW
30.00µW
300.0µW
3.000mW
30.00mW
AUTO
3.000µJ
30.00µJ
300.0µJ
3.000mJ
30.00mJ
AUTO
3.000µW
30.00µW
300.0µW
3.000mW
30.00mW
AUTO
3.000µJ
30.00µJ
300.0µJ
3.000mJ
30.00mJ
AUTO