MirOil 75HS - Manual (Page 3)

Priming for Hand Operated Pumps
An oil film is needed as a seal between the internal parts to prime the pump. During storage and shipping the oil may degrade and become
ineffective as a seal. If there is no pumping, disconnect the discharge hose assembly at the quick coupler and pour a quarter cup of oil into
the top of the pump through the hose connection. CAUTION: After adding oil, reconnect the hose coupler carefully. Before turning the
pump handle, make sure the nozzle is aimed at the fryer or it is installed into the nozzle holder. Use this procedure when the pump does not
prime because it has not been used for an extended period.
If your oil / fat is solid at room temperature:
If a plug of solid fat or shortening forms in the hose, It will prevent pumping.
Procedure to prevent plug of solid oil, fat or shortening:
The oil film on the inside wall may collect at a loop in the hose and form a plug of solid fat. This will prevent the pump from
priming. After filtering, disconnect the discharge hose and hang it from a hook to drain. Use a small collector pan or place hose
nozzle in holder tube on Mobility Basin to avoid oil dripping on the floor.
Procedure for correcting blockage from plug of solid fat:
Try to pour some water through the discharge hose. If the water will not pass through the hose it is blocked with fat. Melt the fat
plug by placing the hose in a large tub or sink with hot water.
Safety Caution:
Residue of water in the hose can cause a dangerous splatter of hot oil.
After the fat plug is melted, make sure the water is fully drained before the hose is recoupled. Before turning ON the power filter
always make sure the discharge hose nozzle is directed at the fryer. If the pump is still not primed, allow the pump to run for
about 3 to 5 minutes so the pump heat may melt any residue of fat in or near the pump body.
Safety first - Make sure the hose nozzle is in the holder tube on the Pump Module when the pump is running.
Loss or Damage During Shipment
Inspect all cartons for damage before unpacking. Your MirOil pump was thoroughly inspected before leaving our factory. The
carrier is responsible for safe delivery. All claims for any loss or damage in transit must be made to the carrier. MirOil will assist with
claims
IF damage has been promptly reported to the carrier.
This product is warranted only against defects in workmanship or materials for 1 year from date of the filter machine is placed
in service or not longer than 15 months from date of purchase. Liability under the basic 1 year limited warranty is limited to
replacing or repairing parts FOB Allentown PA. Parts must be returned to our factory with shipping costs prepaid.
The 1 year warranty does not cover the costs of service labor or shipping
to replace parts.
The use of the filter pump for pumping any liquid other than fryer oil will contaminate the pump and piping. This will
contaminate the oil and may void this warranty
No warranty described above covers the replacement of parts that become inoperative because of wear (except filter bags) or
abuse or for parts subjected to abuse/misuse, negligence, accident or if the product has been improperly repaired or altered
by user or a 3rd party. No other warranty, expressed or implied, is authorized to be made by any parties on behalf of MirOil.
The manufacturer and the manufacturer's sales agents and/or agencies accept no liability for the use or misuse of this
machine. Expressly excluded from warranty are implied warranties of merchantability and fitness for purpose. Manufacturer,
agents and sales agencies disclaim all liability for accidents resulting from use or the misuse of this equipment.
Toll Free Call for warranty information 1.800.523.9844
1 Year Limited Warranty on your Filter Machine
Important Limits for Coverage Under All Warranties
Division of Oil Process Systems Inc.
602 North Tacoma Street Allentown, Pennsylvania 18109
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com