Sears 358.357182 - Manual (Page 10)

E. BAR AND CHAIN UfBfUCANT
• TheguidebarnfMfcuttingcfialnfwjwreconstant
lubrication to mmatn in operating condition.
LuiDrcatxsn IS crovided by trte auaxnatfc oiler system
wner: tre ori tank is kept filled.
—Luck of lubricant wQI puicidy niio the bar and
chain,
—Too itttie lubricant will cause overheatirig
shown oy smoke coming from the cham andtof
discoloration of the guide bar rails.
• Use Sears Bar and Chain litbricam f#71>36SS4>
gal. or #71-36S55 k M to fill the oil tonic Clean SA£
30W oil may also be used, but is less affective. JVmmr
use wasm oS for this purpose.
• *nfreezingweatherollwiIltWck8n,maidngan«ei.
sary to thin bar and chain oil with a atnail amount
of f1 Oie$elPuetori^resene.Sarandch3inoi!must
be free Rovring fer adeqtaiE iubncsSofi.
1. USE THE FOiXOWING;
30® Of above — lubtKant undilutad
30® to 0®F. — 9S% Udjricant to S%
tf Oiasei futi or Ketosene;.
Below 0®F. — 90% Lubricant to 10%
fi Diesel futi or iferos^tt.
2. HOW TO RLL THE OIL TANK
a. Turn saw on its side with oil cap up. Figure
13.
b. Loosen cap slowly; wait tor pressure in the
tank to be released before removing the
cap. .
c. Fill the oil tank.
d. Replace the oil cap securely.
3, IMPOmr^POINre-TOHEMEMBER
a. Fit! the oil tank each lime you rtfllf the fuel
tank to ensure there will be sufficient oil for -
the chain whenever you start and run the
saw.
" »
b. n is normal for a small amount of ail to ap­
pear under the uw after the angin« stops
due to oil draining from the bar and chain.
Figurais
USING YOUR SAW
A. PRE-OPERAnON CHECKS
Each time before operating your saw, always:
1. «'Check over safety rules and pteeauiions in
this manuat. Make certain you completely
understand and can apply each one.
6, «•Cheek №a fuel lank and oil tank. Both tanks
should be filied.
2. ''Cfwcfcpwlecthragetr.Alwaysuseeye.hoaritsg,
and head protection devices: safety footwear; pn>-
teahra gloves: and snugfittingefothkig.
1 «'Cheticthesawtortoeeebolts.mito.orflttings.
Tighten, repair or rapiaee parts as necessary. Tools
required are lisrad inthe “Assembly"
4. «•Check the eirfStcr. Clean the fOfer if dirty, before
starditg the engirm Fbr location, see the “Air niter"
SBCtXüO*
5. Check ttie saw chain. The chain should be snaip
and ai the correct tension. (Refer to the “‘Chain Ten-
son * Sedion). ' ■
«•Check the handies. Handles should be dry
and free of fuel mixture and oil. .
I. «'Check weather conditions. Do not use your
saw at night or dunng bad conditions such
as strongjwind. ram, snow. etc.
g. «'Cheek the work araa. Keep children,
bystanders, and antmaisasafe distance away
tram the work area when starting or ooeralmg
the s a w a minimum of 30 feet.
10