Air filter, Filter – Sears 358.357182 User Manual
Page 18
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
• Use only ttie R<Kiuce<j4aeid3aek Guide B*r
specified for your saw in “Specificst'ons."
a. Remove the guide bar to service.
b. Ciean ou Doles at least once for eacn
five Dours of ooeration.
c. Remove sawausi from the guide bar .
groove oenosicaily with a putty knife or
a wire. Rgured<t.
a. Remove burrs by fifing the side edges
of the guide bar grooves square with a
flat file. RgureSS.
TO W[
CORRECT
GUIDE BAR
GROOVE
WORN
GROOVES
RILE EDGES'
SQUARE
Figure S5
Restore square edges to an uneven rail
top by filing with a Hat file. Rgure 3S .
B,
AIR
FILTER
• A dirty air filter:
—redueas cutting power
-o Increeses fuel consumption
• Cfeen the eif filter;
—Freguently, especially under very dusty
cofiditiOftSe
— Always after 10 tanlcs of fuel ntixtuie or 5
hours of opemtion, whichever is less.
iCAUtlONd To avbid creadng a flte hazard, do not
use g
3
»Iineoranyotherf!amfnable liquid tocfean
thefilter.
1. Clean off the carburetor cover and the area
around it to Keep dirt and sawdust from fall*
ing into the carbu^tor chamber when the
cover is removed.
2. Remove thecarburetor cover screws and car*
buretor cover. Rgtjre36.
3. Pull out the air filter,
4. Wash the filter in soap and water.
NOTE: Be careful when replacing the car
buretor cover as incorrect placement will
prevent the choKe frotn working properly.
9, Move the choke knob a« the vmy to the right,
to. Check the «wia shutter to be sure it is closed.
Figures 36&43.
11. Reinstall the
carburetor cover
and
tighten
the
cartJUteter cover
screvss.
12. Check aie operation of the choke.
NOTE If the choke knob sticks or will not
move, remove the cover and repeat steps
11 and 12 above.
*
CARfiUREIOR
COVER SCREW
iCAimONaPo not use gasoline or other fiamma^'
bie liquid to clean the flit«’ ^ avokl cmating a Hr«
hazard.
5. Squeejte the filter dry.
6. Add a small amount of oil to coat the filter.
NOTE Avoid soaking the filter with oil.
7. ^ueeze out excess oil.
8. Replace filter by tucking in edges and
smoothing it flush with the eattxiretornous*
RgureSfi
c.
SPARK AERESTOR
,1!
•
Carbon depotitsbuitdupantheepsiicamstor
as me
saw is used and must be removed to avoid
Mumta
cevta
H
iHSr*
creatingahre
hazard or causing engtng damage.
•
Replace thesparkanestorifbnajci occur.
sMiw
*««f $T0« scasEit _
• №e#pthesparkarre«oreie«iatalftimas.
01 ean*
*~as required
—at least oneehtr each 2SG0 hmin of opecahon
Kerns feqiared: wire brush. 3/8' wrench
1. Ooconnect the spark plug wire.
2. RemovBlheMofflarCover-Figure 37.
3
.
Rerowe the screen from the baffle.
4. dean the screen with a wire brush or replace f
breaks are iound.
5. Reassemble parts.
IS