Sears 358.357182 - Manual (Page 21)

3.
HIGH SPe£DMiXTUR£ ADJUSTMENT
!СДШЧОМ~ Adjustments as small as Ш6 ol a
tam can aHect engine реНоггвапсе. It is impor.
tan) to turn
the sow onty t/16 of a turn per adjust*
meni and test the pertormarwe of the saw before
making further adjustments.
a Маке a test cut .
5 AciuS! me Highspeed Мшиге Screw I'lbotaiurn
S3 tallows:
— Cocicwse it saw smoires or loses power
—Coufflafacckwise ft the saw nas speed out
of (he cut Dof lacks power in me cut
c. Repeat tea cut.
d Continue ifi6 of a turn adiusunems unw the saw
runs smoothly Ю cut.
-C^TIOH?; A too lean high speed setting (clock*
wise adjustm#nt)wtlti»iseengined«m«geto
any 2 <cycie engine ftem overheating and tack
of lubrication. Never sat the high speed mixture
screw so far eiecicwise thatyouhave high engine
speed but tack power whilaeutting.
An effective approach toliowt:
— Turn screw couhtereiockwise until engine
loses power while cutting.
— Then, lum screw ciockwise in 1/16 of a turn
increments aniy until the engine has power
while cutting.
NOTE; tf the saw wilt not operate property
making these ac^ustrnents. take the saw to your
Sears S*viceCeffl;er/Departmeitt.
F. STORACie
Whan your saw tis to ba stored for over 30 days.
atways:
1. flunthehieioutoflliehielt3hic.carbure^,andhiei
^ne$ by starting the eftglrie and aSowing ittorort a '
idle^eedur«aRS«)p&(See"inieiSiglburBTg»i^^
NOTS: If you do not war« to remove the gasoTme
fmm your unit. SBMRS CRAFTSMAN Riel 2.
StabiE^ (#71*335003 may be added to gasoShe 3.
left in Ше tank to minimcre gum deposiis and 4 .
adds. If the tank is £№tost empty, mix ашрШгвг
with hesh gast^ in a sepreaia conrainer and
5 .
add to the tank. >
NOTE: iris impoftanttopreventpm depositsftom
formir^ine^entiadfuetsystemspansauchasthe g,
carburetor, fuel SRen fuel hose, or tank during 7 .
storageMkfhoibiendedfueb(calledgaspholor
using ethanol er methanol) can ahtact rnoistim .
which leads to separatidn and formadon of acttfo
during storage. Acidic gas can damage the fuel
sy«enu
3 fan enghtetWiile in storage.
tCAUTlONd Wear protective gloves when han­
dling the ehaia The chain is sharp and can
col you even when it is not moving.
Drain oil tank.
Remove, clean, and dry the bar and cnain,
1 b protaa the chain from rust sKxe it in a containsf
®ted with oii, I
Apply a coating of ail to the entire surface of
the oar and wrap it in heavy paper, cloth,or
plastic.
Clean the outside surfaces of the engine.
Sore the saw in adry place, out of the rcaen cl cftii*
dren. and away from where fuel vapore can reacn
open flames from hCTw^ heaters, furnaces, etc
G. MAINTENANCCACCeSGORIfiS
Available through уош* nearest Sean Store, Catalog Sales OfSce, or Service CentedDepartment, but may not
be furnished with your saw.
Key Fart Catalog
No. He. No.
t ST036094e 71-36403
2 31059 —
3 71-3SS24
4
*—
71-3656S
5 ' —
71-36SS7
6 71*3629
■ 71-3619
— 71-36620
71 -aesss
71-36554
71*3^56
'
-Wk
71G6366
71G6374
' 71-33500
Oeseription
Spark Piug*Champ»onCJ -8
Spark Plug Wrench
File Í5 32* dia.
3 Twin Pack
FBe Guide (file holder)
Depth Gauge Tool
Reptaceme«
Xtra GUARD* Chain ( 16 ’)
Replacamer« Xlra GUARD* Chain (18'3
Carrying Case.
2-Cycie Engine Oil
Bar and Cham Lubricant — 1 gallon*
Bar ahd Cham Lubncam — i quart*
Guide Bir-Ui-Kick* (if")
Guide Bar-Lo-Kicic* (18*)
Fuel Staoiiaef
'Availapie tfrougn ypur Sea-re Sevice CentehCaialogue.
21