Aiwa NSX-A10 - Manual (Page 11)

PROGRAMMED EDIT
RECORDING
The Programmed edit function enables CD recording while
checking the remaining time on each side of the tape as the
tracks are programmed.
3
,
7
,
8,9
1 Insert the tape into deck 1.
Insert the tape with the side to be recorded first facing out
from the unit. Press the TAPE button, and wind up the tape
with the ◄◄ button.
2 Press the CO button on the main unit and load
the disc (s).
3 Press the EDIT/CHECK button twice while
pressing the SHIPT button on the remote control.
PRGM is displayed.
4 Press the numeric buttons on the remote control
to designate the tape length.
10 to 99 minutes can be specified.
Example: When using a 60-minute tape, press the 6 and 0
buttons.
Maximum recording
Tape length time for side A
PH bn W) ^ t-BJSG il
LJ
... -
■ M _i I '.I-:..'.-..;'.
Tape side A (front side)
5 Press one of the DISC DIRECT PLAY buttons to
select a disc and press the numeric buttons to
program a track.
Example: To select the 10th track of disc 2, press DISC
DIRECT PLAY 2 and the numeric buttons -i-IO and 0.
Remaining
time of side A
Programmed tracks
_ ,1 ,■<;>. ei !> ^
' H -! IU ''-S'ii B _i
mm
Total number of
programmed tracks
6 Repeat step 5 for the rest of the tracks for side
A.
A track whose playing time is longer than the remaining time
cannot be programmed.
7 Press the EDIT/CHECK button while pressing the
SHIFT button to select side B and program the
tracks for side B.
After confirming B on the display, repeat step 5.
8 Press the EDIT/CHECK button while pressing the
SHIFT button to select side A and press the #
button on deck 1 to start recording.
CD play and recording of edited tracks for the first side start
simultaneously. When the end of the tape is reached, deck
1 enters the recording stop mode. After entering the recording
stop mode, go to step 9.
9 Press the EDIT/CHECK while pressing the SHIFT
button on the remote control for recording of
the second side.
After confirming B on the display, go to step 10.
1 0 Turn over the tape in deck 1 and press the •
button.
Recording starts.
To stop recording
Press the B/A button on deck 1. Recording and CD play stop
simultaneously.
To check the order of the programmed track numbers
Before recording, press the EDIT/CHECK button while pressing
the SHIFT button to select side A or B, and press the DOWN
or »i UP button repeatedly.
(D
Z
Q
•X.
o
u
lU
QC
Program
number
Disc Programmed track
number numbers
n
u
■ ' H _ . I w i -
I ^...........-
Tape side Track number
2
10
12
To change the program of each side
Press the EDIT/CHECK button while pressing the SHIFT button
to select side A or B, and press the ■ CLEAR button to clear
the program of the selected side. Then program tracks again.
To clear the edit program
Press the ■ CLEAR button twice in the stop mode so that the
red line surrounding Al EDIT on the display goes out.
' The edit function cannot be used with discs containing 31 tracks
or more.
' Recording is inhibited if the erasure prevention tab on either
side of the tape is broken off.
To erase a recording
A previous recording is erased when a new recording is made
on that part of that tape.
1 Insert the tape you want to erase into deck 1.
2 Press the TAPE button.
3 Wind up the tape to the point where the erasure is to be
started.
4 Press the • button on deck 1 to start erasure.
ENGLISH
1 0