Aiwa NSX-A10 - Manual (Page 8)

BASIC OPERATIONS
SHIFT
LOADING DISCS
Press the CD button, then press the ± OPEN/
CLOSE button to open the disc compartment. Load
disc(s) with the label side up.
To play one or two discs, place the discs on tray 1 and 2.
To play three discs, press the DISC CHANGE button to rotate
the trays after placing two discs. Place the third disc on tray 3.
Close the disc compartment by pressing the ± OPEN/CLOSE
button.
Totai piaying time
I ' j • L J W
Tray number of the
disc to be played
ROCK POP JAZZ
'I I L- '"I ' h
J.I ! /_! C. .-I .■
1 ‘23 4~
illSi 911
-­
'll
li 138 ft
i
Total number of tracks
PLAYING DISCS
Load discs.
To play all discs in the disc compartment, press
the ► PRESET button.
Play begins with the disc on tray 1.
Eiapsed piaying time
Number of track
being piayed
To play one disc only, press one of the DISC DIRECT
PLAY buttons.
The seiected disc is played once.
EDIT/CHECK
RANDOM/
REPEAT
To stop play, press the ■ CLEAR button.
To pause play, press the II SET button. To resume play, press
again.
To search for a particular point during playback, keep the
◄◄ or ►► button pressed and release the button at the desired
point.
To skip to the beginning of a track during playback, press
the ◄◄ or ►► button repeatedly.
To remove discs, press the A OPEN/CLOSE button.
To start play when the power is off (Direct Play Function)
Press the CD button or one of the DISC DIRECT PLAY buttons.
The power is turned on and play of the loaded disc(s) begins.
To replace discs before play, press the ± OPEN/CLOSE button
to open the disc compartment.
To check the remaining time
Press the EDIT/CHECK button while pressing the SHIFT button
on the remote control during play. The amount of time remaining
until all tracks finish playing is displayed. To restore the play time
display, repeat the above again.
Selecting a track with the remote control
1 Press one of the DISC DIRECT PLAY buttons to select a
disc.
2 Press the numeric buttons and the +10 button to select a
track.
Example:
To select the 25th track, press the +10, +10 and 5 buttons.
To select the 10th track, press the +10 and 0 buttons.
The selected track starts to play and continues-to the end of
that disc.
Replacing discs during play
While one disc is playing, the other discs can be replaced without
interrupting play:
1 Press the DISC CHANGE button.
2 Remove the discs and replace with other discs.
3 Press the ± OPEN/CLOSE button to close the disc
compartment.
• When loading an 8-cm (3-inch) disc, put it onto the inner circle
of the tray. '
• Do not place more than one compact disc on one disc tray.
• Do not tilt the unit with discs loaded. Doing so may cause
malfunctions.
RANDOM/REPEAT PLAY
Use the remote control.
Press the RANDOM/REPEAT button while pressing thé
SHIFT button.
Each time it is pressed, the function can be selected cyclically.
(D RANDOM play — RANDOM lights up on the display.
All the tracks on the selected disc or on all the discs can be
played randomly. ,
® REPEAT play — ^ lights up on the display.
A single disc or all the discs can be played repeatedly.
© RANDOM/REPEAT play — RANDOM and light up on
the display.
@ Cancel — RANDOM and Ci- go out from the display.
During random play following operations are not possible:
- to select the tracks directly with the numbered buttons.
- to skip to the previously played tracks with the ■« button.
7
ENGLISH