Lumagen Radiance 2020 - Manual (Page 22)

Section 5 – Video Configuration
Radiance 2020 rev 102214 17
on the Radiance. Different settings and calibrations for several virtual HDMI inputs can be stored for the same
physical HDMI input. The command is:
MENU →
→ → → Input →
→ → → HDMI Setup →
→ → → Physical In →
→ → → (1, 2, 3, 4)
HDMI Video Type
By default the HDMI input format is detected automatically. For DVI sources, the Auto mode selects RGB format.
For sources that do not report their format correct, the input format can be selected manually. The command is:
MENU →
→ → →
Input →
→ → →
HDMI Setup →
→ → →
Type→
→ → →
(Auto, YCbCr 444, YCbCr 422, RGB)
HDMI Level
This command specifies if RGB HDMI inputs use video levels or PC levels. The input video level should be set to
match the expected range of your video source. A mismatch can cause the image to be too dark or bright. An
output video level mismatch can also have the same effect. The command is only applicable for the RGB input
format. The command is:
MENU →
→ → → Input →
→ → → HDMI Setup →
→ → → Level →
→ → → (Video, PC)
HDMI input EDID Display Information
NOTE:
Lumagen recommends using default video EDID or user-defined video EDID. This
enables the Radiance to report video EDID back to the sources even when the
display is off, and it can also improve power-up and switching speed.
EDID is information that can be read over DVI/ HDMI cables to influence how source devices deliver video, which
helps produce an optimal picture. There are 4 settings for the Lumagen EDID interface. The default setting enables
all of the display modes the Radiance supports. The
User defined setting allows the user to individually select
which capabilities will be advertised to the source. You can scroll through the list of capabilities with the up/down
arrows and toggle advertising the feature with the left/right arrows. With the Passback setting, the Radiance will
read the EDID from the display/AVR connected to the selected output and pass that back to the source. The
command is:
MENU→
→ → →
Input→
→ → →
HDMI Setup→
→ → →
Video EDID→
→ → →
(Default, User defined, Passback Out2,
Passback Out1)
HDMI input hotplug mode
NOTE:
Do not set Hotplug to “always on” unless necessary since this eliminates the
ability of the Radiance to inform the source of a change in the EDID data.
The Hotplug signal is part of a HDMI/DVI interface. Hotplug alerts a DVI/HDMI source device to downstream EDID
changes when toggled. For some devices, such as a PC, it may be necessary to keep hotplug high at all times. The
Radiance provides two hotplug settings, "Normal" and "Always On". The "Normal" behavior is to toggle the Hotplug
signal sent back to the HDMI source when the EDID information needs to be updated. The source will then read
the EDID and make any necessary changes. If the device connected to the Radiance output toggles the Hotplug to
the Radiance then there may be some new EDID information to pass back to the sources and, if hotplug is set to
"Normal", hotplug on all Radiance inputs would be toggled to inform the sources of the change.
Some sources, such as PC's, stop sending video on HDMI/DVI, or enter sleep mode, when the hotplug signal is not
asserted, so setting hotplug on the Radiance to "Always On" is a potential solution. As mentioned above, generally
Hotplug should be set to “Normal.”
Sometimes the connectivity of a system can cause a "HDCP hotplug authentication loop." An example of this is
when connecting the Radiance output to an audio receiver and then hooking the HDMI output of the receiver to
one of the Radiances' inputs. Then, if the Radiance toggles its Hotplug back to the receiver’s output, the receiver
would check the Radiance’s EDID and then toggle its hotplug back to the Radiance to inform it about this new
EDID. The Radiance again toggles Hotplug in response. This can create a continuing loop of HDMI activity.
MENU→
→ → →
Input→
→ → →
HDMI Setup→
→ → →
Hotplug mode→
→ → →
(Normal, Always On)