Lumagen Radiance 2020 - Manual (Page 25)

Section 5 – Video Configuration
Radiance 2020 rev 102214 20
Input Masking
The masking command allows you to cover up the sides of the video source. It is different then cropping in that
the video is not stretched to fill the screen. It can be useful for pass-through modes where you do not wish the
Radiance to scale the picture if there is some video noise on top/bottom/side of the picture that you want to cover
up. Another situation may be that you wish to cover up and change the gray level of the black bars added by a
video source, surrounding a letterboxed image.
When you select the command you must first select which mask number you wish to use. There are 15 available
masks. They can be shared among different input memories. After selecting the mask number you then can adjust
how much the mask covers of the 4 sides of the input. The last step is to alter the gray level for the 4 sides. If an
input mask is on, its gray level takes precedence over the gray level of the aspect bar. The aspect bar gray level
can be adjusted under Output→
→ → →
Configs→
→ → →
[Config]→
→ → →
Other→
→ → →
Graybar. Also, if aspect bars are requested (via
differing input and output aspects) the masking is added to the aspect bar width. The command is:
MENU → → → → Input → → → → Video Setup → → → → [Resolution] → → → → Size → → → → [Aspect ratio] → → → → Masking → → → → OK
Input Control Menu
Deinterlacing Mode
The default deinterlacing mode is “Auto.” This mode automatically switches between video and film deinterlacing
and is best for mixed-mode sources that change between video and film. For sources that are known to be
interlaced-video, choosing “Video” deinterlacing mode can improve image quality. For sources that are known to
be film sources, choosing 'Film' deinterlacing mode can improve image quality. For 60Hz interlaced film sources the
output must be one of 24, 48, 60, or 72 Hertz, and for 50Hz interlaced sources the output rate must be 50 Hertz.
For “Film” mode, Sharpness, Noise Reduction and Adaptive Contrast settings are not available. The command is:
MENU →
→ → → Input →
→ → → Video Setup →
→ → → [Resolution] →
→ → → Control →
→ → → Deint →
→ → → Mode→
→ → → (Auto,Video,Film)
Inter Frame Motion Detection (IFMD)
For deinterlacing video sources (not applicable for film) the IFDM control trades-off between minimizing combing
artifacts (small values) verses maximizing detail (larger values) using the IFMD setting. The default setting is 6.
This control is most effective with “Video” deinterlacing mode. The command is:
MENU →
→ → → Input →
→ → → Video Setup →
→ → → [Resolution] →
→ → → Control →
→ → → Deint →
→ → → IFMD→
→ → → (0-15)
Deinterlacing Field Flip
Some source devices do not follow conventions for the order of video fields. This can be seen as excessive
combing in the video. While generally not required, this command allows the input fields to be swapped so these
out-of-spec sources can be properly deinterlaced. The command is:
MENU →
→ → →
Input →
→ → →
Video Setup →
→ → →
[Resolution] →
→ → →
Control →
→ → →
Deint →
→ → →
Field →
→ → →
(On, Off)
Genlock
Genlock is used to minimize video delay, for 480i/1080i to 24Hz conversion, and to avoid an occasional dropped or
repeated frame. It can slow down source and mode changes, so Lumagen recommends setting Genlock to ‘off’ for
cable and satellite set top boxes. The command is:
MENU →
→ → →
Input →
→ → →
Video Setup →
→ → →
[Resolution] →
→ → →
Control →
→ → →
Genlock →
→ → →
(Auto, Disabled)
Game Mode
To minimize video processing latency, when playing video games, turn “Game Mode” on. Interlaced sources
480i/576i/1080i are treated as 240p/288p/540p. Deinterlacing, and Enhance settings are not available. Typically
game mode is enabled for a specific input memory that is then selected while playing games. For games that have
a vertical rate that matches the Radiance output vertical rate, turning “Genlock” on can further minimize video
latency. Game mode is not intended for video/film program material, such as television shows.
The command is:
MENU →
→ → → Input →
→ → → Video Setup →
→ → → [Resolution] →
→ → → Control →
→ → → Game Mode →
→ → → (On, Off)
Reinterlace
Converts 480p and 576p sources back to interlaced so the Radiance can do the deinterlacing. This can provide
dramatic improvements to a picture that has been poorly deinterlaced prior to coming into the Radiance.
Reinterlacing also allows for taking in 480p/576p movies and going out at 24/48/72Hz. With this command you can
"allow" or "disallow" quick remote key control for a particular resolution as well as turn it on/off. If "Reinterlace <>