Lumagen VisionDVI & VisionHDP - Manual (Page 10)

VisionHDP ™
User Manual and Installer Guide
© 2004-2007 Lumagen®, Inc. 7 Rev 1.14
Rear Panel
All connections are made on the rear panel, which is shown below.
Lumagen, Incorporated
www.lumagen.com
Manufactured in U.S.A.
User must read and accept
license agreement before
using this product.
No user serviceable parts
inside. Refer servicing to
factory authorized agent.
SDI SDI
INPUT 7
SVIDEO
INPUT 5
VIDEO
INPUT 3
P
B
INPUT 2
DVI
INPUT 1
DVI
OUTPUT
DVI
CONTROL
RS-232
POWER
5 VDC Y P
R
INPUT 8
SVIDEO
INPUT 6
VIDEO
INPUT 4
P
B
Y P
R
This device complies with part 15 of the FCC Rules, Canadian ICES-003, and CISPR 22. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
BLUE
INPUT 9 INPUT 0
GREEN RED HCSYNC VSYNC
(Optional) (Optional)
NOTE: If BNC analog output option installed, do not use DVI analog output.
Connections from left to right
• POWER: Connect the supplied external 5 Volt DC, at 5 amp, power supply.
• RS-232: Used for software updates and control.
• DVI-I Video output: Provides either digital (DVI-D) or analog (DVI-A) video output.
• BNC analog output (optional): Replaces DVI-A output when installed.
• INPUT 0 to INPUT 9: Standard input connections.
Input 1 and 2: DVI-D with HDCP support
Input 3 and 4: SD/HD Component, or RGB
Input 5 and 6: Composite video
Input 7 and 8: SVideo
SDI INPUT 9 and INPUT 0 (optional): Optional Serial-Digital-Interface inputs.
RS-232
The RS232 serial port allows the use of an external home theater RS232 controller. This is the
same as a PC DB9 serial port, except no “flow-control” is used. For updates, connect to a PC
using the supplied DB9-F to DB9-F null-modem cable.
Analog Video Output
The analog output supports RGBHV (default, MENU 012 OK), RGBS (TTL composite sync,
MENU 013 OK), RGsB (sync-on-green, MENU 014 OK), or component (MENU 011 OK), using
BNC connectors. For component output the Y channel is connected to green, the P
R
channel to
red and the P
B
channel to blue. Digital output uses a DVI-D connection, which can also drive a
HDMI display using a “DVI-D to HDMI” adaptor cable.
Video Inputs
• It is possible to connect two RGsB (sync-on-green), two RGBS (TTL level sync), or a
single RGBcvS (video level sync using input 3) video source(s), or a combination, using
one or both of the component/RGB inputs (inputs 3 and 4). For RGsB, the input is
specified as RGsB in the input TYPE menu as (MENU
→ IN → TYPE → RGsB). The
separate composite sync types are specified as RGBS (MENU → IN → TYPE → RGBS)
or for RGBcvS as SCART (MENU → IN → TYPE → SCART).
• For all RGB formats, the Y channel is used as Green, the P
B
channel as Blue and the P
R
channel as Red.
•
For the separate composite sync types, one of the composite inputs is redefined as
the S (TTL level), or cvS (video level), sync input. For these types, input 3 uses
input 5, and input 4 uses input 6, as composite sync. A single RGBHV (TTL level