Marantz AV8003 - Manual (Page 55)

CONNECTIONS
SETUP
BASIC
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
51
ENGLISH
PROGRAMME TYPE (PTY) DISPLAY
The RDS system categorizes programmes according
to their genre into different programme type (PTY)
groups. To display the programme type information
of the current station, switch the remote controller to
TUNER mode and press the < / > button until 004 is
displayed. Press the PTY button.
RT (RADIO TEXT) PS (Program Service Name) Frequency
PTY AUTO SEARCH
Your unit is equipped to automatically search for
stations transmitting any of 29 different programme
types. To search for a PTY, follow these procedures:
1.3.4 1.3.4.
2.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX M-DAX
MODE MODE SURROUND SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT INPUT SELECTOR SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF POWER ON/OFF STANDBY STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
2.
1. Press the PTY button in the TUNER MODE on
the remote controller. The current station’s PTY
will be displayed, or the currently selected PTY
group will be displayed in blinking if no station
or RDS data is present.
2. To change to a new PTY type, press the
TUNING 3 or 4 button on the front panel or
numeric buttons on the remote controller until
the desired PTY is shown in the display.
3. Once the desired PTY group or type has
been selected, press the PTY button while
the display blink (approx. 5 seconds). The
PTY Auto search will start, and the tuner will
pause at each station broadcasting RDS PTY
information corresponding to the selected
choice.
4. To advance to the next RDS station with the
desired PTY, press the PTY button again within
5 seconds.
NUMBER DISPLAY PROGRAMME TYPE
1 POP Pop Music
2 ROCK Rock Music
3 MOR M. O. R. Music
4 LIGHT Light classical
5 CLASSIC Serious classical
6 NEWS News
7 AFFAIR Current Affairs
8 INFO Information
9 SPORT Sport
10 EDUCATE Education
11 DRAMA Drama
12 CULTURE Culture
13 SCIENCE Science
14 OTHERS Varied
15 OTHER Other Music
16 WEATHER Weather
17 FINANCE Finance
18 CHILDREN Children’s programmes
19 SOCIAL Social Affairs
20 RELIGION Religion
21 PHONE IN Phone In
22 TRAVEL Travel
23 HOBBIES Hobbies
24 JAZZ Jazz Music
25 COUNTRY Country Music
26 NATION National Music
27 OLDIES Oldies Music
28 FOLK Folk Music
29 DOCUMENT Documentary
ZONE SYSTEM
The Zone System mode allows the same source or
different sources to be heard in two ZONEs other
than where this unit is installed.
To use the zone system, connect the audio from the
ZONE OUT A and B AUDIO output terminals to the
ZONE A and B amps.
Connect the VIDEO output (ZONE OUT) terminal to
the monitor in Zone A.
(ZONE OUT terminal is linked to the source selector
in Zone A.)
If a surround channel back speaker or speaker C
(see page 18) are not used in the ZONE where this
unit is installed, the zone speaker system can be
used with the amp for the surround back channel.
Also, the COMPONENT VIDEO MONITOR OUT
2 terminal can be used for the monitor output of
ZONE A.
This unit supports zone system functions such as
source selectors, OSD menu systems, sleep timers
and remote control.
ZONE PLAYBACK USING THE ZONE OUT
TERMINALS
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX M-DAX
MODE MODE SURROUND SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT INPUT SELECTOR SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF POWER ON/OFF
STANDBY STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
3. 4. 1.
1. Pressing the ZONE button on the unit one time
accesses the ZONE A settings. Pressing it two
times accesses the ZONE B settings. Then,
pressing it a third time turns the zone feature
off.
2. When the ZONE setting mode is engaged, one
of the following screens appears on the display
for 10 seconds.
* Display when ZONE A is selected
Z A D V D - 1 8 d B
* Display when ZONE B is selected
Z B D V D - 1 8 d B
3. Select an input source with the INPUT
SELECTOR knob.
4. Turn the VOLUME knob to set the volume of
the ZONE used in the zone system as you
like.
Note:
• The sleep timer, monaural output and other features
can also be set using the MAIN MENU.
(See page 35)
AV8003N.indb 51 AV8003N.indb 51 08.4.28 10:49:31 AM 08.4.28 10:49:31 AM