ONICON D-100 BACnet - Manual (Page 13)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax (727) 442-5699 • [email protected]
D-100 Display Module BACnet Installation and Operation Guide 05/14 - 0635-6 / 18341
Page 13
STEP ACTION REACTION COMMENT
0 Obtain MAC address & device
instance number from the
network administrator. None. The MAC address is a three digit
number from 001 – 254. The
device instance number can be
anything from 0 – 4,194,303.
1 With the display running, open
the front panel, locate and
momentarily press the
pushbutton switch DEV ADD /
PROG ENAB. None. DEV ADD / PROG ENAB is
located in the lower left corner
of the D-100 processor board
next to the DB9 connector (See
appendix page A-1).
2 Momentarily press the
PROGRAM pushbutton on the
front panel of the display. If
this is not done, the display
will revert to the RUN mode
after 5 minutes. The D-100 will change to the
PROGRAM mode. The top line of
the LCD will indicate PPPPPPPP.
The second line will read DEVICE
ID and the first digit of the 3 digit
MAC address will be blinking. The PROGRAM pushbutton is
the rightmost pushbutton on the
front panel user interface.
3 Successively press the SCROLL
pushbutton to increment the
number to the desired value
from 0 – 9. The blinking number increments
by one each time you press the
SCROLL pushbutton. The SCROLL pushbutton is the
leftmost pushbutton on the front
panel user interface.
4 Momentarily press the RESET
pushbutton once. The second digit will now be
blinking. The RESET pushbutton is the
center pushbutton on the front
panel user interface.
5 Successively press the SCROLL
pushbutton to increment the
number to the desired value
from 0 – 9. The blinking number increments
by one each time you press the
SCROLL pushbutton. The SCROLL pushbutton is the
leftmost pushbutton on the front
panel user interface.
6 Momentarily press the RESET
pushbutton once. The third digit will now be
blinking. The RESET pushbutton is the
center pushbutton on the front
panel user interface.
7 Successively press the SCROLL
pushbutton to increment the
number to the desired value
from 0 – 9. The blinking number increments
by one each time you press the
SCROLL pushbutton. The SCROLL pushbutton is the
leftmost pushbutton on the front
panel user interface.
8 Once the correct address is
displayed, momentarily press
the PROGRAM pushbutton. The INSTNCE page is now
displayed with the first digit
of the device instance number
blinking. The PROGRAM pushbutton is
the rightmost pushbutton on the
front panel user interface.
9 Use the SCROLL pushbutton
and RESET pushbutton as
described above to enter the
new device instance number. Each digit will increment and the
RESET pushbutton will advance
the blinking cursor to the next
digit. The SCROLL pushbutton is
the leftmost pushbutton on the
front panel user interface. The
RESET pushbutton is the center
pushbutton on the front panel
user interface.
10 Once the correct address is
displayed, momentarily press
the PROGRAM pushbutton. The FRONT PANEL RESET page
appears. It is not necessary to change
anything on this page.
11 Momentarily press the
PROGRAM pushbutton. The SAVE CHANGES page
appears. The new addresses must be
saved to take effect.
12 Momentarily press the SCROLL
pushbutton. The “N” changes to “Y” on the
SAVE CHANGES page. The “Y” must be selected in order
for the new addresses to take effect.
13 Momentarily press the
PROGRAM pushbutton.
The new addresses are saved and the
display will revert to the RUN mode.