Orion System Digital Room v.1 - Manual (Page 10)

DIGITAL ROOM SENSOR
Operator Interface 10
Appendix
EXPANSION D'STAT SPACE SENSOR
POWER / COMM STAT
M A DE
IN US A
WA TT M A ST ER
C O N T R O L S IN C
HI (V AV )
LO W (VV T ) VELOCITY
AI RF L O W
WDO
G
A D D R ESS
OF F
O N
EP RO M
PAL
ACTUATOR
485
REC
DRV
EEPROM
93C66
(- )L
O
GND
OUT
IN
AIR FLOW
SENSOR
OE742/OE744 VAV/Zone Controller Actuator Package
Display Override
OVERRIDE ALARM
NOTE: If Also Using An OE256-01
Or OE256-02 C
Sensor, T
Connects To The VAV/Zone
Controller First Using A TSDRSC
Cable Of The
Length. The
Digital Room Sensor Then Connects
To The CO Sensor With Another
TSDRSC Cable.
O
2
2
he CO
Sensor
Required
The Total Length Of
Cable For Either One Or Both Cables
Combined Cannot Exceed 160 Feet.
See The
For Further Wiring Details.
2
CO
2
Sensor Technical Guide
OE217-00
Digital Room Sensor
TSDRSC Cable
OE217-00 Or OE217-01
Digital Room Sensor
OE332-23E-VCMX
VCM-X E-BUS Controller
TSDRSC Cable
Display Override
OVERRIDE ALARM
NOTE: If Also Using An OE256-01
Or OE256-02 CO Sensor, The CO
Sensor Always Connects To The
VCM-X Controller First Using A
TSDRSC Cable Of The Required
Length. The Digital Room Sensor
Then Connects To The CO Sensor
With Another TSDRSC Cable.
The Total Length Of Cable For Either
One Or Both Cables Combined
Cannot Exceed 160 Feet. See The
For
Further Wiring Details.
2 2
2
CO
2
Sensor Technical Guide
RELAY CONTACT
RATING IS 1 AMP
MAX @ 24 VAC RS-485 COMMUNICATION LOOP. WIRE
“R” TO “R”, “T” TO “T” “SHLD” TO “SHLD”
FAN
RELAY 2
RELAY 3
RELAY 4
RELAY 5
RELAY
COMMON
IC DIGITAL
SENSOR
2 IC
EXPANSION
2 STATIC
PRESSURE
AI1 = SPC (SPACE TEMPERATURE SENSOR)
AI2
AI3
AI4
AI5 AI7
A01
A02
= SAT (SUPPLY AIR TEMPERATURE SENSOR)
= RAT (RETURN AIR TEMPERATURE SENSOR)
= OAT (OUTDOOR AIR TEMPERATURE SENSOR)
= SUCTION PRESSURE SENSOR
= SPACE TEMPERATURE SENSOR SLIDE ADJUST
OR VOLTAGE RESET SOURCE
= ECONOMIZER (2-10 VDC OUTPUT)
= SUPPLY FAN VFD (0-10 VDC OUTPUT)
ANALOG INPUT JUMPER SETTINGS
MUST BE SET AS SHOWN FOR
PROPER OPERATION 24 VAC POWER ONLY WARNING! POLARITY MUST BE OBSERVED
OR THE CONTROLLER WILL BE DAMAGED
www.orioncontrols.com
AI1
AI2
AI3
AI4
THERM
THERM
THERM
THERM
THERM
THERM
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
0-10V
0-10V
0-10V
0-10V
0-10V
0-10V
0-5V
0-5V
0-5V
0-5V
0-5V
0-5V
AI5
AI7
ANALOG INPUT JUMPER SETTINGS
WattMaster Label #LB102033-01
OE332-23-VCMX-A VCM-X CONTROLLER
WA
RN
IN
G
OBSERVE POLARITY
RELAY CONTACT
RATING IS 1 AMP
MAX @ 24 VAC RS-485 COMMUNICATION LOOP. WIRE
“R” TO “R”, “T” TO “T” “SHLD” TO “SHLD”
FAN
RELAY 2
RELAY 3
RELAY 4
RELAY 5
RELAY
COMMON
IC DIGITAL
SENSOR
2 IC
EXPANSION
2 STATIC
PRESSURE
ANALOG INPUT JUMPER SETTINGS
MUST BE SET AS SHOWN FOR
PROPER OPERATION 24 VAC POWER ONLY WARNING! POLARITY MUST BE OBSERVED
OR THE CONTROLLER WILL BE DAMAGED
AI1
AI2
AI3
AI4
THERM
THERM
THERM
THERM
THERM
THERM
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
0-10V
0-10V
0-10V
0-10V
0-10V
0-10V
0-5V
0-5V
0-5V
0-5V
0-5V
0-5V
AI5
AI7
ANALOG INPUT JUMPER
SETTINGS
WattMaster Label
#LB102073-01-A
Rev.: 1A
www.aaon.com
www.orioncontrols.com
VCM-X MODULAR E-BUS CONTROLLER
Orion No.:OE332-23E-VCMX-MOD-A
AAON No.:
V07150
AI1 = SPC (SPACE TEMPERATURE SENSOR) AI2
AI3
AI4
AI5
AI7
A01
A02
= SAT (SUPPLY AIR TEMPERATURE SENSOR)
= RAT (RETURN AIR TEMPERATURE SENSOR)
= OAT (OUTDOOR AIR TEMPERATURE SENSOR)
= SUCTION PRESSURE SENSOR (FROM EXP. MODULE)
= SPACE TEMPERATURE SENSOR SLIDE ADJUST
OR VOLTAGE RESET SOURCE
= ECONOMIZER (2-10 VDC OUTPUT)
= SUPPLY FAN VFD (0-10 VDC OUTPUT)
LED BLINK CODES
LED NAME STATUS1 STATUS2
NORMAL OPERATION 0 1
SAT FAIL 1 2
OAT FAIL 2 2
SPC FAIL 3 2
MODULE ALARM 4 2
MECH COOL FAIL 1 3
MECH HEAT FAIL 2 3
FAN PROOF FAIL 3 3
DIRTY FILTER 4 3
EMERGENCY SHUTDOWN 5 3
LOW SAT 1 4
HIGH SAT 2 4
CONT. TEMP COOL FAIL 3 4
CONT. TEMP HEAT FAIL 4 4
PUSH BUTTON OVR 1 5
ZONE OVR 2 5
OUTPUT FORCE ACTIVE 0 6
E-BUS CONNECTOR
Figure 17: Digital Room Sensor to VAV/Zone Controller Wiring
Figure 18: Digital Room Sensor to VCM-X E-BUS Controller Wiring