Paso Sound PDVD01U - Manual (Page 41)

TASCAM DV-D01UT/C
1
Maintenance
Handling Discs
Remove the disc from its case by holding
it at the edge while pressing the center hole
lightly.
Do not touch the shiny surface of the disc
or bend the disc.
Put the disc back in its case after use to
prevent warping.
Be careful not to scratch the surface of the
disc when placing it back in its case.
Avoid exposure to direct sunlight, extreme
temperature and moisture.
·
•
•
•
•
•
To clean the disc
Wipe the disc with a soft cloth in a straight
line from center to edge.
DO NOT use any solvent — such as
conventional record cleaner, spray,
thinner or benzine — to clean the disc.
Cleaning the unit
Stains on the unit should be wiped off with a soft cloth. If the
unit is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe clean with
a dry cloth.
Since the unit may deteriorate in quality, become damaged or
get its paint peeled off, be careful about the following.
DO NOT wipe it with a hard cloth.
DO NOT wipe it forcefully.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substance such as insecticides
to it.
DO NOT allow any rubber or plastic to remain in contact
with it for a long time.
•
·
•
•
–
–
–
–
–
Troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
Power does not come on. The power cord is not connected. Connect the power cord correctly. (See page 8.)
The remote control does not
work. The batteries are exhausted. Replace the batteries. (See page 6.)
Sunlight is shining directly on the remote sensor. Hide the remote sensor from direct sunlight.
The disc reading time is
too long. The disc is dirty. Clean the disc by referring to “Maintenance” above.
No sound. The audio cable is not connected. Check the connection.
No sound is produced
when playing back a
DVD recorded with high
sampling (88.2 kHz or
more) linear PCM audio
using the DIGITAL OUT
(OPTICAL) jack. The audio signal is not derived from the unit’s
DIGITAL OUT (OPTICAL) jack. Use analog AUDIO OUT when playing back such
discs.
No picture is displayed on
the TV screen. The video cable is not connected correctly. Connect the cable correctly. (See page 7.)
The disc or file is not playable. Use a playable disc or file. (See pages 3 and 4.)
No picture is displayed on
the TV screen, the picture
is blurred, or the picture is
divided into two parts. The scan mode is set to “480p”(NTSC) or
“576p”(PAL) though the unit is connected to the
TV which does not support the progressive video
input such as a conventional TV. Change the scan mode to “480i” (NTSC) or “576i”
(PAL) though. (See page 10.)
Video and audio are
distorted. The disc is scratched or dirty. Replace or clean the disc.
A VCR is connected between the unit and the TV. Connect the unit and TV directly. (See page 7.)
The picture does not fit the
TV screen. The monitor type is not set correctly. Set “MONITOR TYPE” properly. (See page 26.)
No picture is displayed on
the TV or no sound come
out through HDMI connec-
tion. A video or audio format not compatible with this
unit and/or TV is played. Check the video or audio format of the signal to see
if it is compatible with this unit and/or TV.
A HDCP-compatible TV is not connected. Connect a HDCP-compatible TV. (See page 7.)
The unit failed to recognize the TV connected with
the HDMI cable. Disconnect the HDMI cable and connect it again.
A HDMI cable longer than 5 m (15 ft) is used. Use a HDMI cable shorter than 5 m (15 ft) to assure
stable operation and picture quality.
The picture is distorted
when the TV is connected
through HDMI terminal. Proportion of the picture may not be shown
correctly depending on a disc/file when the TV is
connected through HDMI terminal. Connect the TV through component video, S-video,
or composite video jacks (see page 7), then set the
scan mode to “480p” (see page 10).
If there are any other cases than the noted above or if this unit does not seem to work properly, turn off the unit and turn it back on.
References