Sea Eagle Transom Sport Boats (2009 and earlier) - Manual (Page 5)

5
The two crossbars on FB4
greatly support the transom on
sport boats to carry heavier
engines. To install, simply bolt
the two short aluminum
crossbars on FB-4 floorboard
using the knurled nuts included
in the reinforcement kit while the
boat is partially inflated.
Please note this item is not compatible with older floorboards. Please
call to determine if your floorboards will accept reinforcement kit.
Finish inflation - Sport Runabouts
Inflate all hull chambers to 100%, or 3.2 PSI. The chambers on our
transom boats cannot be over inflated with a foot pump. A chamber
reaches its optimum pressure when you can no longer pump any
more air into it with a foot pump. The foot pump at this stage becomes
very hard and it will not be possible to inflate the chamber any further.
IMPORTANT: For the 9.2 SR, 10.6 SR, 12.6 SR & 14 SR.only inflate
the keel to 80% of max pressure. Please note, inflating the keel to
100% pressure will hinder the performance of the boat under power
and bend FB-2 unduly.
Deflation
To deflate a chamber, simply turn the valve
stem clockwise with your thumb to secure it
in the down position. This will let the air out
of your boat. Our boats do not require a
pump for deflation.
Inflation & Floor Assembly for 8.10 YT
Yacht Tender and 10.6 SR-RIK
The 8.10 YT and 10.6 SR-RIK feature a High Pressure Drop Stitch
Floor. This simple flooring system is far lighter and does not need any
assembly. The 8.10 YT & 10.6 SR-RIK, as mentioned earlier, come
with a special A50 High Pressure Foot Pump.
Partially inflate the bow, port and
starboard chambers to about 10% -
20% using the A50 High Pressure
Double Chamber Foot Pump. Make
sure to close the black cap of the
foot pump to inflate these chambers.
Closing the black cap engages the
larger chamber of the A50 foot pump
and permits more air volume.
HINT: It is very helpful to place an object under the
bow such as a box or a bucket to prop it up. This
makes insertion of stringers far easier because the
floorboards will be on the same plane.
Please note, SE 10.6 SR-RIK Drop Stitch Floor has an
aluminum crossboard under it for extra support. In
addition, at back of the SE 10.6 SR-RIK transom are
anchor fitting which the slide fittings on the drop floor
have to be attached to - see picture at right. This is a
one-time only assembly. Afterwards, simply leave drop
stitch floor in boat and roll up with boat.
Place the inflatable floor in the SE 8.10YT or
the SE 10.6 SR-RIK. The Recessed One Way
valve of the floor should be facing up in the
bow of the boat (in the case of the SE 10.6 SR-
RIK it is just behind the valve for the outside
keel - please note in case of SE 10.6 SR-RIK,
inflate floor first and keel second). Insert the
Valve Adapter in the Recessed One-Way Valve to connect the A50
Foot Pump. The High Pressure Drop Stitch Floor has to be inflated to
7 psi. In the case of the SE 10.6 SR-RIK inflate the outside keel to 7
psi after you have fully inflated the drop stitch floor. Hint - pump
becomes difficult to inflate once you reach 7 psi.
To inflate the high pressure floor, make
sure to remove the black cap of the A50
Foot Pump. By doing so the A50 Foot
Pump uses only the smaller chamber, thus
allowing it to reach 7 psi without much
effort. The High Pressure Drop Stitch Floor
becomes hard as a basketball. Once the floor
(and in the case of the SE 10.6 SR-RIK) is
fully inflated, withdraw the adapter and close the valve cap.
Continue to finish inflation of the side chambers. Again make sure to
close the black cap of the A50 foot pump to inflate the side chambers
to 3.2 psi. Continue to pump with the foot pump till you cannot get any
more air in.
Accessories
WS2505 Aluminum
Bench Seat: Sea Eagle
9.2 SR, 10.6 SR, 12.6 SR,
14 SR & 8.10 YT transom
boats come with fabric
bead seat attachment
system for the Aluminum
Bench Seats. There are
two fabric beads on each
pontoon. You can attach up
to two Aluminum Bench
Seats to these models.
The new Aluminum Beach Seats
have nylon slotted fittings under
them on both sides as shown in
the picture.
Fabric
Guard
and strap
to secure
fuel tank
Drop Stitch floor attachs to
2 slide fittings below at
base of transom