Chapter 6: appendices – Smart Avi AVRouter User Manual

Page 17

Advertising
background image

AVRouter Manual Version 1.0

Page 17

5.0 SmartN

5.0 SmartN

5.0 SmartN

5.0 SmartN

5.0 SmartNeeeeet-

t-t-

t-

t-X

XX

XX Frame Switches

Frame Switches

Frame Switches

Frame Switches

Frame Switches

The communications port on the SmartNet-X allows for multiple chassis to be connected together.

Chapter 6: Appendices

Chapter 6: Appendices

Chapter 6: Appendices

Chapter 6: Appendices

Chapter 6: Appendices

Although the following communication protocol has been specifically written for the SmartNet-X unit from SmartAVI, it
is accurate for the AVRouter and other units from SmartAVI.

1.0 Document Conventions
Any numbers preceded by ‘0x’ are hexadecimal.

(base 16)

All data byte string listed in examples are in hexadecimal.

(base 16)

2.0 Comms Ports Settings.

2.0 Comms Ports Settings.

2.0 Comms Ports Settings.

2.0 Comms Ports Settings.

2.0 Comms Ports Settings.
The Host Controller Serial Port should be configured as detailed in the table below

3.0 RS232/422 converter.

3.0 RS232/422 converter.

3.0 RS232/422 converter.

3.0 RS232/422 converter.

3.0 RS232/422 converter.
The Frame control interface uses RS422. A full duplex 5 wire balanced communications standard that allows
communications to be multi-dropped to more than one Frame.

Since PC’s only come with RS232 ports a small converter is required to convert the RS232
signals to RS422.

If you purchased any of the SmartControl software options you will have received a suitable converter and cable.

In the event that you wish to purchase your own converter and/or make your own comms cable please see Appendix
A at the rear of this document for more information.

4.0

4.0

4.0

4.0

4.0 Conne

Conne

Conne

Conne

Connecti

cti

cti

cti

cting

ng

ng

ng

ng up

up

up

up

up

4.1. Plug the RS232 end of the RS232 to RS422 converter directly onto the selected comms port on the rear of your
computer.

4.2. Plug the comms cable (D9 end) onto the end of the RS422 end of the RS232/RS422
converter.

4.3. Plug the RJ45 end of the comms cable into the IN port on the front of the SmartNet-X or SmartNet-V.

e

t

a

R

d

u

a

B

e

t

a

R

d

u

a

B

e

t

a

R

d

u

a

B

e

t

a

R

d

u

a

B

e

t

a

R

d

u

a

B

0

0

6

9

0

0

6

9

0

0

6

9

0

0

6

9

0

0

6

9

s

t

i

B

t

r

a

t

S

s

t

i

B

t

r

a

t

S

s

t

i

B

t

r

a

t

S

s

t

i

B

t

r

a

t

S

s

t

i

B

t

r

a

t

S

1

1

1

11

s

t

i

B

a

t

a

D

s

t

i

B

a

t

a

D

s

t

i

B

a

t

a

D

s

t

i

B

a

t

a

D

s

t

i

B

a

t

a

D

8

8

8

88

y

t

i

r

a

P

y

t

i

r

a

P

y

t

i

r

a

P

y

t

i

r

a

P

y

t

i

r

a

P

e

n

o

N

e

n

o

N

e

n

o

N

e

n

o

N

e

n

o

N

s

t

i

B

p

o

t

S

s

t

i

B

p

o

t

S

s

t

i

B

p

o

t

S

s

t

i

B

p

o

t

S

s

t

i

B

p

o

t

S

1

1

1

11

Advertising