Ascaso – Ascaso Steel BAR User Manual
Page 9
STEEL BAR UM2id OK 2012.FH11 Mon Jun 04 16:49:04 2012 Página 9
3
. Safety / Start up
I m p o r t a n t S a f e g u a r d s
The appliance must be only installed in
places where its use and maintenance
is restricted to qualified personnel.
1-. Read all instructions.
2-. Do not touch hot surfaces. Use han
dles or knobs.
3-. To protect againts fire, electric shock
and injury to persons do not immerse
cord, plugs or (state specific part or
parts in question) in water or other liquid.
4-. This appliance is not intended for
use by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person res
ponsible for their safety
5-. Unplug from outlet when not in use
and before cleaning. Allow to cool before
putting on or taking off parts and before
cleaning the appliance.
6-. If the power cord is damaged, it must
be replaced by the manufacturer, its
after-sales service or similar qualified
personnel in order to avoid danger.
7-. Do not operate any appliance with
a damaged cord or plug or after the
appliance malfunctions, or has been
damaged in any way. Return appliance
to the nearest authorized service facility
for examination, repair or adjustment.
8-. The use of accesory attachments
not recommended by the manufacturer
may result in fire, electric shock or injury
to persons.
9-. Domestic use. Do not use outdoors
(this item may be omitted if the products
is specifically designed for outdoor use).
10-. Do not let cord hang over edge of
table or counter or touch hot surfaces.
11-. Do not place on or near a hot gas
or electric burner or in a heated oven.
12-. Always attach plug to appliance
first, then plug cord into the wall outlet.
To disconnect, turn any control to "off"
then remove plug from wall outlet.
13-. Do not use appliance for other than
intended use.
14-. Not use this appliance if ambient
temperature exceeds 40 ºC or less than
0 ºC
15-. Do not use connecting hoses used
and always use those supplied with the
appliance.
16-. Save these instructions.
Before setting the appliance going, the
person installing should read this manual
carefully. The operator should be a res
ponsible adult. Children should be su
pervised to ensure that they do not play
with the appliance. In the event of any
anomaly, contact your distributor
Start up
Check the electrical voltage is the same
as the voltage displayed on the machine
specifications label.
1) Coffee machine (direct water net)
: Connect the wastepipe tube
2
and
connect the machine to direct mains
water input with tube
19
. You must open
the water tap.
2) Coffee machine with water tank :
fill the water tank (side area)
16
with
water (min. 3 liters). The use of mineral
water is recommended. Water quality
affects the taste and quality of the coffee.
3) For both models : Plug it into the
mains. Switch on the machine with swit
ches
0
and
3
. The pilots
00
and
6
will light up.
After 3-4 seg, the boiler fills up automa
tically. Upon finalizing, the pump stopped
and the pilot
4
was illuminated, this
indicates the moment in which begins
to heat the boiler.
Is normal that during the filling up pro
cess, the coffee machine stop and the
left electronic device flashes.
You must do a reset operation through
the boiler switch On/off
0
. The coffee
machine will continue the filling up
process.
When pilot
6
switch off, the coffee
machine is ready for coffee use.
For steam and hot water, the pilot
4
swich off and the manometer
7
will
indicate 1,5 bar pressure of boiler. The
boiler will be ready to serve steam and
hot water ( 20 minutes, aprox.)
Is normal that to the star in steam servi
ce, the stam pipe leave water. Place the
pipe on the wastepipe tray.
!
Important : if by any motive, not
water arrives to the coffee machine
boiler, the left electronic device will flash
and the coffee machine will stop. Dis
connect with the switch
0
and check
the water supply ( direct water outlet or
water tank). Once it re-established the
water supply, switch on
0
.
!
Note : The use of mineral water
is recommended. Water quality affects
the taste and quality of the coffee, in
addition to preventing future breakdowns
4.
Programming the amount
of coffee
Electronic push-button control functions.
S: small coffee
L: large coffee
XL: non-stop coffee (push button again
to stop flow)
Programming the amount of coffee .
With the machine on, push the XL
programming button for 5 or 6 seconds
until the LED flashes.Push the S small
coffee button. The LED will light up, at
the same time the XL programming LED
stops flashing. Let the coffee flow.
Once you have the desired amount,
push the XL button until the led stops
blinking. The machine is now program
med.
To programme large coffee L, repeat the
operation.
Machines two groups: When program
ming the left group, the right group is
automatically programmed with the sa
me parameters. Then, you can progra
mming the right group with new settings
(this not change the left settings).
To personalise the amount of coffee
(non-stop), push the XL button. Once
you have the desired amount, push the
button again to stop the flow of coffee.
5.
Programming switchboard
for capsule counter
- Switch off the machine
- Press keys S-L-XL all at once and switch
ascaso
ascaso
ENGLISH
ENGLISH
14
1 5