Grass Valley UIM v.2.1.1 User Manual
Grass Valley Equipment
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- Finding Information
- Safety Summaries
- Version 2.1.1 Release Information
- What’s new
- Operational considerations
- Profile system and UIM-DIS-GEIP power-on sequence
- Enable Fibre Channel network TCP checksums
- 1000BT Ethernet port settings
- Redundant Ethernet network requirements
- Profile XP Platform 100BT network option
- UIM Windows user accounts
- Operating the UIM in unattended mode
- High definition video transfers
- Transfers with K2 systems
- Software requirements
- Installing UIM System Software
- Virus software support
- Performing critical Windows updates
- Known problems
- Product Description
- UIM-DIS-GEIP Installation: Standalone Profile Storage
- Are you redeploying Profile systems?
- Rack-mount the UIM-DIS-GEIP
- Specify host names for each UIM-DIS-GEIP
- Specify the subnets required
- Setup the master hosts file
- Connect network cables - Dell 2650
- Connect network cables - Dell 2850
- Connect network cables - Dell 1950
- Configure UIM-DIS-GEIP hostname and IP addresses
- Configure Profile host names & IP addresses
- Test the UIM-DIS-GEIP
- Create UIM-DIS-GEIP system disk image
- Solving common setup problems
- UIM-SAN-GEIP Installation: Grass Valley Open SAN System
- Onsite planning
- Rack-mount the UIM
- Converting the UIM-DIS-GEIP to a UIM-SAN-GEIP
- Modify the master hosts file
- Configure the UIM network settings
- Connect UIM-SAN-GEIP network cables Dell 2650
- Connect UIM-SAN-GEIP network cables Dell 2850
- Connect UIM-SAN-GEIP network cables Dell 1950
- Install CVFS client software on the UIM-SAN-GEIP
- Perform miscellaneous system settings
- Enable Fibre Channel network TCP checksums
- Verify access to shared storage
- Test the UIM-SAN-GEIP functionality
- Create UIM-SAN-GEIP system disk image
- UIM-SAN-FCIP Installation: Grass Valley Open SAN System
- Onsite planning
- Rack-mount the UIM
- Modify the master hosts file
- Configure the UIM network settings
- Connect UIM-SAN-FCIP network cables Dell 2850
- Connect UIM-SAN-FCIP network cables Dell 1950
- Install CVFS client software on the UIM-SAN-FCIP
- Perform miscellaneous system settings
- Enable Fibre Channel network TCP checksums
- Verify access to shared storage
- Test the UIM-SAN-FCIP functionality
- Create UIM-SAN-FCIP system disk image
- Service Information
- Interpreting front panel and rear panel indicators
- Troubleshooting
- Before calling product support
- If you have a problem: UIM-DIS-GEIP
- Step 1: Power-on the UIM, and log on as Administrator
- Step 2: Make note of any recent system changes
- Step 3: Check the status of Grass Valley Services on the UIM
- Step 4: Use “ping” utility to test Fibre Channel connectivity
- Step 5: FTP a media file via Fibre Channel
- Step 6: Use the “ping” utility to test Ethernet connectivity
- Step 7: Check Ethernet switch status
- Step 8: FTP a file using the 1000BT interface connected to the streaming LAN
- Step 9: Test the streaming performance
- If you have a problem: UIM-SAN-GEIP
- Step 1: Power-on the UIM, and log on as Administrator
- Step 2: Make note of any recent system changes
- Step 3: Check access to the shared storage
- Step 4: Check the status of Grass Valley Services on the UIM
- Step 5: Use the “ping” utility to test Ethernet connectivity
- Step 6: Check Ethernet switch status
- Step 7: FTP a file using the 1000BT interface connected to the streaming LAN
- Step 8: Test the streaming performance
- If you have a problem: UIM-SAN-FCIP
- Step 1: Power-on the UIM, and log on as Administrator
- Step 2: Make note of any recent system changes
- Step 3: Check access to the shared storage
- Step 4: Check the status of Grass Valley Services on the UIM
- Step 5: Use the “ping” utility to test Ethernet connectivity
- Step 6: Check Ethernet switch status
- Step 7: FTP a file using the Fibre Channel interface connected to the FC IP network
- Step 8: Test the streaming performance
- Using a generic rebuild CD
- Creating a system disk image
- Restoring the system disk image
- Installing the disk image on a replacement UIM
- Part 1: Preparing to install the system disk image
- Part 2: Replace the system disk image
- Part 3: Enter Windows software license number
- Part 4: Modifying Windows operating system settings
- Part 5: Update IP UIM System Software
- Part 6 for Dell 2650/2850: Setup Ethernet port teams
- Part 6 for Dell 1950: Setup Ethernet port teams
- Part 7: NIC Name & IP Address Setup
- Part 8: Set the Control Team IP Address
- Part 9: Set the Streaming Team IP Address
- Part 10: Rename the Qlogic FC NIC
- Part 11: Set the Qlogic FC NIC IP Address
- Part 12: Setup Connection Priorities
- Part 13: Set the Qlogic MTU size
- Part 14: Set up TCP/IP Scaling
- Information for application developers
- Upgrading Existing Profile Systems for Deployment with the UIM-DIS-GEIP
- Preparing the Profile XP Media Platform
- Preparing the Profile Video Server (PDR family)