Curtis RACP1206 - Manual (Page 6)

7 8
OPERATING INSTRUCTIONS
Press the ION button, the ion generator
is ener gized and will help to remove
pollen and impur ities from the air, and
trap them in the filter. Press it again to
stop the function.
8 ION button(optional)
Operating Instructions
- Press the "MODE" button until the "COOL"
indicator light comes on.
- Press the ADJUST buttons "▲" or " " to
select your desired room temperature. The
temperature can be set within a range of
O O O O 17 C-30 C/62 F-88 F.
- Press the "FAN SPEED" button to choose the
fan speed.
▲
- Press the "MODE" button until the "DRY" indicator
light comes on.
- Under this mode, you cannot select a fan speed or
adjust the temperature. The fan motor operates at
LOW speed.
- Keep windows and doors closed for the best
dehumidifying effect.
- Do not put the duct to window.
COOL operation
DRY operation
- Press the "MODE" button until the
"FAN " indicator light comes on.
- Press the "FAN SPEED" button to
choose the fan speed. The temperature
cannot be adjusted.
- Do not put the duct to window.
FAN operation
TIMER operation
- Press the "MODE" button until the "HEAT"
indicator light comes on.
- Press the ADJUST buttons "▲" or " " to
select your desired room temperature. The
temperature can be set within a range of
O O O O 17 C-30 C/62 F-88 F.
- Press the "FAN SPEED" button to choose the
fan speed. For some models, the fan speed
can not be adjusted under HEAT mode.
▲
HEAT operation (cooling only models without)
AUTO operation
- When you set the air conditioner in AUTO
mode, it will automatically select cooling,
heating(cooling only models without), or fan
only operation depending on what temperature
you have selected and the room temperature.
- When the unit is on, first press the
Timer button, the TIMER OFF
indicator light illuminates. It indi-
cates the Auto Stop program is
initiated.
- When the unit is off, first press the
Timer button, the TIMER ON indic-
ator light illuminates. It indicates
the Auto Start program is initiated.
- Press or hold the UP or DOWN
button to change the Auto time by
0.5 hour increments, up to 10 hours,
then at 1 hour increments up to 24
hours. The control will count down
the time remaining until start.
- The selected time will register in 5
second and the system will autom-
atically revert back to display the
previous temperature setting.
- Turning the unit ON or OFF at any
time or adjusting the timer setting
to 0.0 will cancel the Auto Start/
Stop timed program.
- When the malfunction (E1 or E2)
occurs, the Auto Start/Stop timed
program will also be cancelled.
SLEEP operation
- The air conditioner will control room
temperature automatically round the
temperature point set by you.
- Under AUTO mode, you can not
select the fan speed.
When the operation is ON, press the
SWING button can stop the louver at
the desired angle. The louver swing up
O to an angle of 6 for each press. Keep
pressing the button more than 2 seconds
can initiate the auto swing feature.
9 SWING button
(Applicable to the models with auto swing feature only)
Press this button, the selected temperature
will increase(cooling) or decrease(heating)
O O by 1 C/2 F 30 minutes.The temperature
will then increase(cooling) or decrease
O O (heating) by another 1 C/2 F after an
additional 30 minutes. This new temper-
ature will be maintained for 7 hours
before it returns to the originally selected
temperature. This ends the Sleep mode
and the unit will continue to operate as
originally programmed.
NOTE: This feature is unavailabe under
FAN or DRY mode.
OPERATING INSTRUCTIONS
Other features
After the unit has stopped, it can not be restarted
operation in the first 3 minutes. This is to protect
the unit. Operation will automatically start after
3 minutes.
Wait 3 minutes before resuming operation
The louver can be adjusted manually or
automatically according to the different models.
Adjust the air flow direction manually
(Fig.5):
The louver can be set to the desired position
manually. The max setting angle is about
O 60 , please do not force to set any larger.
Do not place any heavy objects or other loads
on the louver, doing so will cause damage to
the unit.
Ensure the louver is fully opened under
heating operation.
Keep the louver fully opened during
operation.
Adjust the air flow direction automatically
(Fig.6):
When operation is ON, the louver opens fully.
Use the SWING button on the remote
controller can stop the louver at the desired
angle.
O The louver move up to an angle of 6 for
each press until it move to a position which
would affect the cooling or heating effect
of the air conditioner, it would automatically
change the swing direction.
If keep pressing the SWING button more
than 2 seconds, the auto swing feature is
activated. The louver swings as shown in
Fig.6
Air flow direction adjustment
Fig.5
Adjust manually
Swing automatically
Fig.6
If the unit breaks off unexpectedly due to the
power cut,it will restart with the previous
function setting automatically when the power
resumes.
Auto-Restart(on some models)