El Paso Chile Company DMS 3080-80 - Manual (Page 29)

PAGE 29
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120
EQ
OUT
AUDIO
L
IN R
102 EQ. MODULE
R
L
EQ LINK
ATTENUATOR ATTENUATOR
IN OUT
TEL
G COM HOT
47kohm 100mV
(AUX1) (AUX2)
LEVEL
TEL OUTPUT
INPUT-4(AUX1)
BALANCED
INPUT 5
MIC-AUX2
BY INTERNAL
SWITCH
250ohm 1.5mV
47kohm 100mV
INPUT-5(AUX2)
ON OFF
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
30TJ US
MIX
BUSS
LINE OUT
600
PRE
OUT
POWER
IN
SUB OUT
PRE EQ
SUB OUT
POST EQ
TONE
BYPASS
EQ LINK
WARNING: THIS APPLIANCE
MUST BE EARTHED
INPUT 4 (MIC) INPUT 3 (MIC) INPUT 2 (MIC)
G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT
INPUT 4
REMOTE
VOLUME
AUX2
47Kohm 100 mV
INPUT5 (MIC-AUX2)
600 ohm 100mV
SATELLITE RECEIVER
CD PLAYER
MUSIC OUTPUT
Connect to INPUT 4/AUX 1 Connect to
Module
EQ OUT
Connect Music
Source Output
to Module EQ IN
METHOD 1
Equalize
Music Only
BOSE MODULE METHOD 01
SET TONE BYPASS
SWITCH TO ON
TRACK 0 1
INSTALLING AND USING A BOSE® EQUALIZER MODULE
Fig. 26 - Method 1 Module Wiring Diagram
BOSE® is a Registered Trademark of BOSE Corporation
METHOD 1
EQUALIZING THE PROGRAM ONLY
BY USING THIS METHOD THE
MUSIC PROGRAM ONLY IS EQUAL-
IZED BY THE MODULE.
BE SURE THAT THE TONE BYPASS
SWITCH IS IN THE ON POSITION
1) Connect the Output of the PRO-
GRAM SOURCE unit to the Module
IN Jack.
2) Connect the EQ. OUT Jack of the
Module to INPUT 4/AUX 1 of the
Amplifier.
LEVEL CONTROLS - Adjust INPUT
4/AUX 1 Front Panel Control to 1
o'clock. Turn Rear Panel ATTENUA-
TOR Control slowly clockwise until the
desired Output Level is achieved After
above adjustments are completed use
the INPUT 4/AUX 1 Front Panel
Control to increase or decrease the
Music Level as desired.
CAUTION: PRIOR TO INSTALLING THE BOSE® MODULE IN THE AMPLIFIER FOLLOW THE INSTRUCTIONS SUPPLIED WITH
THE MODULE AND THEN READ THE INSTRUCTIONS IN THIS MANUAL’S “INSTALLING A MODULE” SECTION
METHOD 2
USING THE EQ LINK
BY USING THIS METHOD ALL THE
AMPLIFIER INPUTS ARE EQUAL-
IZED BY THE MODULE.
BE SURE THAT THE TONE BYPASS
SWITCH IS IN THE ON POSITION
1) Connect the Output of the PRO-
GRAM SOURCE unit to the INPUT 4
(or INPUT 2) L and R Jacks.
2) Connect the EQ. OUT Jack of the
Module to the POWER IN Jack of the
Amplifier.
3) Connect the EQ. IN Jack of the
Module to the PREAMP. OUT Jack of
the Amplifier.
4) Set EQ LINK Switch on the
Amplifier to IN.
LEVEL CONTROLS - Adjust INPUT
4/AUX 1 Front Panel Control to 1
o'clock. Turn Rear Panel ATTENUA-
TOR Control slowly clockwise until the
desired Output Level is achieved After
above adjustments are completed use
the INPUT 4/AUX 1 Front Panel
Control to increase or decrease the
Music Level as desired.
Fig. 26B - Method 2 Module Wiring Diagram
INSTALLATION AND WIRING
PROFESSIONAL AUDIO & SOUND
® TM
DIGITAL MUSIC SERIES
DIGITAL MUSIC AMPLIFIERS