EXP Computer ThinCom PCMCIA Ethernet Modem Adapter User Manual
Page 35
APPENDIX A
- 31 -
S37:000 S90:000 S108:002 S109:062
S37:000 S90:000 S108:002 S109:062
Telephone Numbers:
Telephone Numbers:
&Z0 12345
&Z0 12345
&Z1 T4444444
&Z1 T4444444
&Z2 T12345
&Z2 T12345
&Z3 T 1 (123) 456-7890
&Z3 T 1 (123) 456-7890
&W
0
0
Store active profile in user profile 0
Store active profile in user profile 0
1
1
Store in
Store in active profile user profile 1
user profile 1
&Y
0*
Select stored profile 0 on power up
1
Select stored profile 1 on power up
&Zn=x
none
Store telephone number
To dial the stored telephone, use the
To dial the stored telephone, use the
ATDS=n command.
ATDS=n command.
x = 0, 9, A, B, C, D, #, *, T, P, R, W, @, ,,!,;
x = 0, 9, A, B, C, D, #, *, T, P, R, W, @, ,,!,;
n = 0-3
n = 0-3
%E
0
Disable Auto-retrain ( V.32 and V.32bis Only)
1 *
Enable Auto-retrain
%G0
0 *
Disable Auto Fallforward/fallback Rate
Renegotiation
1
Enable Auto Fallforward/fallback Rate
Renegotiation
%Q
none
Line signal quality
Range: 0-255
Range: 0-255
0 - 7 No Retrain
0 - 7 No Retrain
8 - 255 Modem performs a Retrain (i.e., if configured for %E1)
8 - 255 Modem performs a Retrain (i.e., if configured for %E1)
-Cn
0*
Diable data modem calling tone
1
Enable data modem calling tone
*
Value saved in NVRAM.
V.42, MNP 'AT' Commands
Command
Default
Function
%A
13
Set auto-reliable fallback character
%C
0
No data compression
1*
MNP 5 data compression control
\A
0
0
MNP block size
Maximum 64 characters
Maximum 64 characters
1
1
MNP block size
Maximum 128 characters
Maximum 128 characters
2
2
MNP block size
Maximum 192 characters
Maximum 192 characters
3*
3*
MNP block size
Maximum 256 characters
Maximum 256 characters
\Bn
none
Transmit break (n=0-9 Break lenght in 100 msec)
\C
0*
Does not buffer data
1
1
Buffers data for four seconds until 200 characters have been buffered or SYN character is detected, then switches to reliable mode. If the buffer fills,
Buffers data for four seconds until 200 characters have been buffered or SYN character is detected, then switches to reliable mode. If the buffer fills,
data is passed to the serial port.
data is passed to the serial port.
2
2
Does not buffer data. Switches to normal mode upon receipt of auto-reliable fallback character and passes it to serial port. This feature is used to
Does not buffer data. Switches to normal mode upon receipt of auto-reliable fallback character and passes it to serial port. This feature is used to
allow non-V.42 modems to connect immediately to a V.42 modem without data loss.
allow non-V.42 modems to connect immediately to a V.42 modem without data loss. Set auto-reliable buffer
\G
0 *
Disable modem port flow control
1
Set port flow control to XON/XOFF
\Jn
0 *
Disable Bps rate adjusting