EXP Computer ThinCom PCMCIA Ethernet Modem Adapter - Manual (Page 36)

APPENDIX A APPENDIX A
- 32 -
1 Enable Bps rate adjusting
\Kn 5 Set break control
In Connect State, if reliable mode then transmit break to remote:
n = 0,2,4 Enter command state, but do not send a break.
n = 1 Destructive/expedited
n = 3 Non-destructive/expedited
n = 5 Non-destructive/non-expedited
In Command State, if reliable mode then transmit break to remote:
n = 0,1 Destructive/expedited
n = 2,3 Non-destructive/expedited
n = 4,5 Non-destructive/non-expedited
In Connect State, if direct mode then receive break at serial port:
n = 0,2,4 Immediately send break and enter command state.
n = 1,3,5 Immediately send break through
In Connect State, receive break at modem port, send to serial port:
n = 0,1 Destructive/expedited
n = 2,3 Non-destructive/expedited
n = 4,5 Non-destructive/non-expedited
\Nn Set Operating Mode: Determines the type of Set Operating Mode: Determines the type of connection attempted by the modem. connection attempted by the modem.
n = 0 n = 0 Normal Mode-No data compression or error correction, but uses speed buffering. Normal Mode-No data compression or error correction, but uses speed buffering.
n = 1 n = 1 Direct Mode- No data compression, error correction, or speed buffering. Direct Mode- No data compression, error correction, or speed buffering.
n = 2 n = 2 MNP Reliable Mode-The modem attempts to negotiate an MNP error-correction 'reliable' link, hanging up if it fails. MNP Reliable Mode-The modem attempts to negotiate an MNP error-correction 'reliable' link, hanging up if it fails.
n = 3 n = 3 V.42 Auto-reliable Mode * If V.42 detection is enabled (- V.42 Auto-reliable Mode * If V.42 detection is enabled (-Jn), a LAPM or MNP link can be detected and negotiated, otherwise only LAPM will be Jn), a LAPM or MNP link can be detected and negotiated, otherwise only LAPM will be
attempted. If configured for -J0 and a protocol connection is not made, the modem will hang up. If configured for -J1 and a protocol attempted. If configured for -J0 and a protocol connection is not made, the modem will hang up. If configured for -J1 and a protocol
connection is not made, the modem will fall back to speed buffering mode.
connection is not made, the modem will fall back to speed buffering mode.
n = 4 n = 4 V.42 Reliable - The modem attempts to negotiate LAPM error correction, hanging up if it fails. V.42 Reliable - The modem attempts to negotiate LAPM error correction, hanging up if it fails.
NOTE: 300 NOTE: 300 bps does not support synchronous operation. The mode will automatically fall back to MNP asynchronous operation. bps does not support synchronous operation. The mode will automatically fall back to MNP asynchronous operation.
\O none Originate reliable link
\Qn 0 Disables flow control
1 XON/XOFF software flow control
2 Unidirectional hardware flow control
3* Bidirectional hardware flow control
\T 0* Disable inactivity timer
0-90 Lenth in minutes
\U none Accept reliable link
\Vn 0 Enables codes defined by ATV command
1 Enables modified MNP codes
2* Enables extended V.42 codes
\X 0* Processes flow control characters *
1 Processes flow control characters and passes them through to the local or remote so they can process the characters.
\Y none Switch to reliable mode
\Z none Switch to normal mode
-Jn 0 Disable the V.42 detect phase
(\N3,\N4 operating mode)
1* Enable the V.42 detect phase